Jump to content
SAU Community

Recommended Posts

Hey everyone,

Recently bought an R32 GTS-4 which I'm pretty happy with. It however has a few little issues I would really love to fix up to get it running 100%. These are:

1) Car won't pull hard all the way to redline, it boosts perfectly in the mid-range but over about 4500rpm the rate of acceleration is much slower than getting up to 4500. Was told this could be because the car is running really rich or something? Any ideas? I have a feeling it could be ignition related, coilpacks?

2) Car sometimes makes a backfire type noise when I put the pedal down about half way, and say rev to 3000, then quickly put the clutch in to change. Could this be because of the car running rich and having excess fuel there?? Not sure if this is a backfire or "missfire".

3) The car has some kind of heavy duty clutch, and when I put the pedal in really quickly it will sometimes stall. However if I put the pedal in more gradually, it won't. Sometimes it'll go down to 0rpm and everything will cut out then it'll come back on by itself, sometimes it'll just stall and Ihave to turn ignition on again.

Would taking the car to a dyno tuner rectify my problems?

Thanks

EDIT - Forgot to mention, the car is pretty much stock apart from a Kakimoto 3" turbo back system. Still has stock air box, and boost etc.

Edited by esprit
your car makes very similer problems to mine!

im going to try and replace my AFM

The guy who sold the car had replaced the AFM before selling it, so I don't think thats the issue. Could be with yours, who knows.

Forgot to mention, another annoying little thing is when the car is idling, it makes some kind of noise like a fan spinning, its quite audible. When you press the clutch in this noise completely goes away.... anyone know what that could be?

  • 3 weeks later...

go to a dyno place and when it's on the dyno and they run it, you will see if the car is running rich.

the clutch sound could be a few things.

Multiple plate clutches seem to make noise when not engaged.

it could also be the bearings in the clutch.

it could be that the flywheel was not machined when the new clutch went in.

stalling problem.. don't know..

missfire is when it misses a beat..

backfire sounds more like a pop or bang.

missfire happens when there is a miss with the spark for one of many reasons.

backfire happens due to excess fuel not being burnt in the combustion chamber and then exploding once in the exhaust area.

so... if you have the boot in and the revs are rising, boost is up and the car sort of cuts and comes back real quick... this is missfire...

if you have the boot in, then shift gears, if you have excess fuel (which happens on stock ecu with a bit more boost), you will hear a pop or bang from the exhaust... this is backfire.

car not pulling to red line..

it seems normal(ish) for a stock turbo'd old r32 rb20 to do that..

gets full boost (10 psi) by about 3000rpm then pulls hard till about 4500rpm then it still revs up and pulls, but not like it did from 3000-4500rpm..

I don't think there is anything weird about that.

you can fix it or make it less obvious by doing these 2 things together..

1.) buy one of those cheap $22 boost controllers that there is a thread about on these forums.

even if you don't increase the boost (which you probably shouldn't with stock intercooler), it is designed to bring on boost quicker than standard as it keeps the wastegate shut for longer.

2.) you should also disconnect your stock blow off valve, and look at the bottom of it.. you will see a tiny little hole next to the big piston of the bov.

block up that little hole with a small flat head screw.

make sure it seals good.

put the bov back on as it was and your all good.

car will build boost MUCH quicker and hold it better and therefore will feel better above 4500rpm.

you gotta remember that your GTS4 is about the same weight as a GTR (1450kg or something)

so the torque free 2L will feel sluggish.

these 2 mods above which cost less than $50 will make a world of difference to cars responsiveness.

You won't put any more stress on anything as you will not be making any more power (maybe a tiny bit) but boost response and reving it feels alot better.

Mine gets around from 4500-6500 almost as quick as from 3000-4500rpm.

same car but more door.

Hey thanks for the response. All problems are now fixed and the car is running great!

I got a multimeter and tested coils, every single on of them = f**ked. Got a set of awesome condition ones off kezza on here (cheers ;) ).

I did an engine oil, oil filter, and fuel filter change yesterday, only to find the original fuel filter was proper rooted, I wouldn't be surprised if it was the original filter that came when the car was first sold! Changed that all and the car flies now, it really moves nicely to redline :) This could be due to the addition of one of those boost controllers sold on here, an hks pod, and an hks ssqv bov. I've got boost set to 11.5psi and am careful with how often I get up it, always let it warm down etc. I'm really pleased with how the car is running now, just have to get a set of new tyres for it :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...