Jump to content
SAU Community

Recommended Posts

I doubt you'll get 190rwkw-200rwkw. With 16 PSI, you are already pushing the turbo itself. Your turbo might not last that long if you keep it at 16PSI most of the time.

I reckon with those mods, you'll get about 170rwkw provided that you had a very good tune done to the car

Link to comment
https://www.sau.com.au/forums/topic/101639-how-many-kw/#findComment-1861480
Share on other sites

I doubt you'll get 190rwkw-200rwkw. With 16 PSI, you are already pushing the turbo itself. Your turbo might not last that long if you keep it at 16PSI most of the time.

I reckon with those mods, you'll get about 170rwkw provided that you had a very good tune done to the car

I'd say your on the ball there. Might push 180kw :)

Link to comment
https://www.sau.com.au/forums/topic/101639-how-many-kw/#findComment-1861510
Share on other sites

Results of all the s15's i could quickly find with similar mods (of course it varies dyno to dyno). t28bb is ball-bearing and steel wheeled, it'll run over 16psi no problems.

for a reading of 199.8rwkw on my car [s15]with standard AFM, standard manifold, standard injectors, standard fuel reg and standard cams

boost = 17psi

I have the following:

S15 JDM t28 turbo

stainless exhaust manifold

fmic

exhaust

pump

264/264 hks cams

pod

I get 197rwkw@11psi on an old S13 SR20

A good friend of mine has 200rwkw from his S15, It has a front mount, complete 3 inch exhaust, pod filter, walbro fuel pump and a wolf 3d plug in computer. It made 200rwkw on 18psi with the standard injectors and turbo

I dynoed my car [s15] the other day and she's pulling 195rwkw @ 15psi and it was a hot day. I'm more than happy with the stock turbo. I have these mods.

Trust R-SPL cooler

Apexi filter

Apexi PowerFC

Apexi AVC-R

HKS dump

HKS front pipe

Apexi GT cat

Fujitsubo Power Getter cat back

Nismo fuel pump

Nismo 555 injectors.

My S15 made 192kw with standard ECU, the same mods you mentioned in your original post (exhaust, fmic, pod filter, apexi avc-r), only thing on top of that was the addition of a GTR fuel pump. That was with 1.05bar boost and AFR of 12.2:1.

200rwkw is about the max you'll get from the AFM and injectors without raising fuel pressure. You won't make much more from the turbo either without cams.

Edited by neil_se
Link to comment
https://www.sau.com.au/forums/topic/101639-how-many-kw/#findComment-1861989
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...