Jump to content
SAU Community

Recommended Posts

if u can grab the ecu serial number (23710-XXXXX) then i can probably check when ur ecu is from. most likely if u havent wired up the consult port ull need to do that, but thats only a minor issue.

  • 2 weeks later...
  • Replies 152
  • Created
  • Last Reply

Top Posters In This Topic

not yet...got word back from one of the two places i contacted about getting it custom made (this one in the US) and i should get an estimate on how much it would cost from them soonish.

still finalising some of the hardware - ive decided on just serial consult interface capability (was thinking of usb, but decided the usb if at all would be an adaptor onto the serial - have already tested this in its basics and its fine, but will cost an extra $20 and probably diy to put together). want to have the pcb made so that all future functionality i might put onto the device is there to start with - ie room for eeprom to store data, buzzer for alarms, etc

ive found a decent LCD (viewing angle 50 from up, 60 from below, and 40 each side which is by far best ive seen, good refresh time, also is wide temp which is great) which ive got a couple of to test with. just hope they are kept in stock as i bought 3 of the last 8, but it might take quite a while to get more in

desktop and ppc software is on hold while im working on this. havent really started ppc app aside from just testing some stuff will work on it. good thing will be that knowing how to make it look will be harder than actually doing it

be working a bit on trying to get a beta of the desktop version available today

got a first quote back on the enclosure being custom made, going to be around the 30$ in large quantities (ie 50-100), which i guess if i cant get anything better will go with it. around $15 more than what i budgeted for, but still have another place to check out so will see if i can get something better there

Edited by NewKleer

still unsure if ill be able to do that, will take a while to write up a construction guide and whatnot, and troubleshooting any problems will be hard. construction itself might not be too difficult so i might just do that myself

essentially it comes down to whether i think ill save more time doing it myself or not whether i can offer it as a kit. wont rule out anything yet though

at this stage i think best case scenario would be end of march for when i get things all ready by (either diy or assembled), but have been busy at work lately so havent had much time to finalise stuff like pcb layout (which then effects the enclosure production).

still unsure if ill be able to do that, will take a while to write up a construction guide and whatnot, and troubleshooting any problems will be hard. construction itself might not be too difficult so i might just do that myself

essentially it comes down to whether i think ill save more time doing it myself or not whether i can offer it as a kit. wont rule out anything yet though

at this stage i think best case scenario would be end of march for when i get things all ready by (either diy or assembled), but have been busy at work lately so havent had much time to finalise stuff like pcb layout (which then effects the enclosure production).

cool take your time.

Attention to detail will pay off for you- its proof to the rest of us that you're going to have a top product at the end of it :P

  • 1 month later...

here's an update, have made a prototype. which removes a lot of the extras, but am just testing the main screen and will soon be able to test the integrated consult interface, just need to wire up the serial plug.

as you can see the size is still quite compact and am on track to make it of similar dimensions to whats shown there.

shot taken on angle as i had no contrast adjust setup on lcd yet (and straight on was just like all black). whats shown there is standalone and only has the consult plug coming off it.

consultlcdproto.jpg

Edited by NewKleer
  • 3 weeks later...

need to have a draft pcb made for the enclosure to be done (so they can make sure everything fits). i hope to have it done by end of month. then maybe 1.5-2 months till enclosure is done, and at the same time id get final pcb and components ready.

unfortunately due to enclosure costing more and having to get the pcb's done elsewhere to the normal place, current estimate is up around the 175 mark, however this shouldnt change much (and no chance of it going beyond 200).

hardest thing is getting the time to get pcb done with work and uni being flatout. i just want time to stop for a week!

  • 2 weeks later...

heres the prototype pcb that sits behind the lcd. the lcd "plugs" into the very left "rectangle" box on this thing (and thats the only connection to it, so replacing it will be easy). ill be getting this made soon for testing (about 5-10 of them), so fingers crossed i didnt make any mistakes.

there are 3 buttons - the left one will be (whenever i add the functionality) the "command" button, and the next two will be the add/minus or up/down or whatever buttons. you can then see the switch roughly in middle, here you switch it to left to use the display like normal, or to the right to use it as a consult interface. theres also a lot of future expanability in the board (a lot of places i can wire other stuff in) so hopefully ill only ever need this one layout for anything i do

will be ordering parts soon, and if the first prototype boards i get have no issues, then i can get a full batch done and get the enclosures made (roughly 6 weeks from then is when enclosures might be done).

lcdpcb1s.jpg lcdpcb2s.jpg

the novelty of blue wears off quickly once u realise how hard it is to see in daylight and on angles.

but any standard sized (182x33.5mm) 40x2 module can go in. just this one im getting will be wide temp and very good viewing angles compared to most.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...