Jump to content
SAU Community

Recommended Posts

Haha, perhaps there is a reason to run at UAS now... we're gapping the plugs on Saturday to 0.65 (iridiums) and changing the top end of the tune. See if that makes a difference, if not we'll just set it back to what it was before.

Also, my rotor-boy friend asked who was doing the runs... he doesn't want them running it above and beyond the car's comfort zone.

EDIT: Going to call TURBOS tomorrow and see if he'll be interested in showing us 1150hp + :woot:

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

I truly doubt it is 1150 hp

I know for a fact that it was around the 500awkw mark on a CRD dyno. Plus croydons dyno would not read that high

Last time turbos was out on the drag strip, he broke down after one run :O

I've been hearing BS from when he first imported the car that it had "1200HP at the wheels" from rumour-mongers. Would be great to see, but I doubt it has anywhere near that. Although, 500awkw is nothing to sneeze at.

Hey guys, definately in for this one, just didnt have time to get my damage fixed so car looks a bit shit (parked skyline vs moving shitbox) one of my mates expressed intrest in putting his magna on the dyno, any room for a ring in???? :)

Update:

Abo Bob

Wink

Satanic

ORGSMK

Jas-25T

Moanie

Benm

Silver gts-t x3

Disturb3d

N1GTR

Cowie165

Security

Azzr32

2rismo

yogi000

evil weevil

R33Deviat

DiRTgarage?

dOOdz

pshht

wilch

nath95

Trust33

Bu5ter

ranicx

Morgs

Blitz

Jago

wraith skyline

TommyK

GoldZilla ?

GTR Legend

ECR033

Links

Neil

Duncan

MR R33

OSH33N

Ezz35

NYL83R

nugget400hp

Primordial

PORTS

MZ- R33 x3

ZXFIRE

monkeykplunk ?

E_Lu-Shun ?

legend01

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...