Jump to content
SAU Community

Recommended Posts

Hi everyone I really need some advice from you guys.

I have a Series 1 R33 Sedan - the one with the ugly taillights lol.

I'm in the processes of doing her up but I can't get past the lights. Anyway I want to do a conversion to Series 2 taillights.

So basically I want to rip them out and chuck in series 2 ones. Has anyone done this before?

What I need to know is, is it possible?

Thanks

PS. Below are the only two pics that I could find the 1st a series 1 (silver one) and the 2nd a series 2.

http://www.skylinesaustralia.com/photopost.../big/perpage/12

http://www.skylinesaustralia.com/photopost...door/perpage/12

the 2nd one is Impul version isn't it?

Hi no the second pic is just a Series 2 sedan.

Most people hate the back of the R33 series 1 sedan & because the series 2 sedan is so rare, most people do not know it exists.

Rarity - that's one reason why I want to do the conversion.

Jlnewton, you must have one of the only series 2 R33 sedans in brisbane. Good on you they look sweet.

Does anyone know any contacts in the spare parts industry?

I contacted about 20 places on saturday and not one of them has series 2 sedan tail lights. Over half didn't even know that there was a difference between the two series.

It's hard enough finding skyline sedan parts as it is.

Thanks

Try Justjap, they may be able to source some for you.

Thanks chaos, i'll try them in the morning!

Do you know anywhere that would possibly have them in stock? Or if it doesn't take too much time could you please give me the names of the main mobs that you know in Australia?

Thanks

i think its called Alljap aswell, there a wrecker on the northside i believe (not 100%) sure. Justjap are located in Sydney but they always over night their parts etc as i've bought a few things off them.

Also go to the buisness trader section on the forum and ask around there, they may have some or can source some aswell.

Also, the only difference I can notice with the lights is that the blinkers are in a different spot.

Would that be a problem or do you think that it would be easy to get around?

And Chris I'll let you know the end result.

Thanks

I have picked up the lights and the centre garnish today & they are in perfect condition. The car I got them off was a 1997 series 2 40th annerversary special edition and it alsol had a special edition spoiler.

Anyway the spoiler looks great but the guy won't sell it without the boot. My question is would the boot also be interchangable with my series 1 boot?

Thanks

Edited by jcsky2005
I have picked up the lights and the centre garnish today & they are in perfect condition. The car I got them off was a 1997 series 2 40th annerversary special edition and it alsol had a special edition spoiler.

Anyway the spoiler looks great but the guy won't sell it without the boot. My question is would the boot also be interchangable with my series 1 boot?

Thanks

Yup. Congrates on the find.

There are a few series 2 sedansin Bris. My new one obviously, my old one is still getting around here, and I have seen a purple one, white one, two other silver ones, a creamy/off white one and a dark blue one.

Yup.  Congrates on the find. 

There are a few series 2 sedansin Bris.  My new one obviously, my old one is still getting around here, and I have seen a purple one, white one, two other silver ones, a creamy/off white one  and a dark blue one.

Yeah thanks.

Both lights and the garnish set me back a very reasonable $450.

Dropped in to see my cousin who is a panel beater yesterday and he reckons that they will slot right in no problems. He also quoted me $100 to prep, paint and fit the lights….I owe him one!

So that’s $550 all up. I took some pics yesterday of the back, so I will post the before and after pics when the cars done.

Jlnewton, what year is yours? And did the back/taillights of a series 1 sedan play a role in your decision twice to purchase a series 2?

The car I got them off was a 1997 40th anniversary and the rear wing and stock body kit was simply just really nice. Shame that one side of the car was in bits and pieces, scattered on the side of a highway somewhere because I really liked those skirts!

Mine is a 97 manual. The main reason for going to the series 2 is the battery has been relocated back to the front of the car, same layout as the R34s. Means a much more usable boot space which is the whole reason I wanted a sedan, to be more practical.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...