Jump to content
SAU Community

Recommended Posts

Ok, so i run std radiator and there is always talk about what temp the coolant should not exceed.

Looking around the net i cant find any info on what general temp an alloy head cannot exceed, ditto RB series engine.

I have just bought a new probe that will measure head temperature, i always pull the pin when the coolant temps nudge 90-100. The actual head temp whoudl give me a better indication when to back off...shouldnt it?

Link to comment
https://www.sau.com.au/forums/topic/103848-head-temperature/
Share on other sites

Hi Roy, I am not sure that I completely understand the question. It is not the maximum temperature that causes cylinder head or head gasket issues, it is the temperature differential that causes warpage or, in extreme cases, cracking. For example exhaust ports can be upwards of 800 degrees C, water jackets max is around 110 degrees, inlet ports 60 degrees, combustion chamber temperature etc

So where you place the sensor determines what temperature you are likely to see.

:unsure: cheers :D

Hi Roy, I am not sure that I completely understand the question.  It is not the maximum temperature that causes cylinder head or head gasket issues, it is the temperature differential that causes warpage or, in extreme cases, cracking.  For example exhaust ports can be upwards of 800 degrees C, water jackets max is around 110 degrees, inlet ports 60 degrees, combustion chamber temperature etc

So where you place the sensor determines what temperature you are likely to see.

:P cheers :rolleyes:

This is why they invented water injection pre-turbo to lower all the combustion chamber temps... by over 35% :ban:

...no thanks...may work great, but watter isnt that compressible last time i checked, andi dont have that much faith in control systems, be it the car tuned for it and then you run out of water...or a problem means one day you start your car and BANG bent rods :P

*cough*mechanical water injeciton*cough* dont buy cheap china stuff that runs off electronic components.

Using your (probe?) placed somewhere on the cylinder head casting will give you a fair idea on whats happening.

I dont think water injection is used to cool down the cylinder head as much as cooling the intake charge.

I see cyl heads on an almost daily basis that have overheated and have gone soft. (i usualy ditch the head any where under 65 brinell)

Good idea to have an alarm at a certain temperature!

I only heat the heads around 80-90 celcius when pressure testing.

The only time i pressure test hot is if the customer has a water prob and we cant find it and/or the head has been welded etc.

Why dont you keep an eye on the temps and watch for any changes?

Make sure you tell us some details.

THe xr6t's have a cylinder head temp sensor right in the middle between the two valves on the back of the head no 6 cylinder. At 300rwkw a 10 second dyno ramp can yeild a rise temperature from around 90deg to 110-115 degrees. I would have though at this temp the coolant would start to boil?

Hi Roy , some years ago Craig Allen from Allen Engineering in Mallala said they were using multiple coolant temp probes along the head of an RB30ET . This was done because when souped up the head was suffering localised overheating I think down the back and some plumbing alterations were used to get more even water flow and temperature along the length of its head .

Most engines probably use water temp probes at the front or where the water outlet to the radiator is . Doing it this way should be ok but when power output is pumped up its difficult to know whats going on at the other end of the heads water jacket . Craig said something along the lines of 86deg at the front of the VLT head and 110 down the back .

I think major dramas occur when there's localised boiling and steam pockets form in the jacket , where there's no water there's no cooling so localised thermal overload can cook/warp/crack the casting . I have seen examples of heads that have small water lines tapped into high points in the jacket to give any bubbles an escape path usually to a header tank which is the highest point in the cooling system .

Any way I suppose another water temp probe down the back of your engines cylinder head would tell you if the coolant temp was even along its length .

An exhaust temp probe between the head and turbo would be handy because if the temp got out of hand something may fail before the water temp gauge could tell you particularly if your racing and need all attention on driving the thing .

The rally people tend to use a bright dash light and loud buzzer to warn them of

imminent doom ie for oil pressure/water temp or whatever they choose to hook up .

I think there is available head temperature probes for air cooled engines such as Dak Daks (VW's!) but I'm not sure if it would tell you anything useful on a water cooled engine . Either Allen Engineering or Nizpro have used a temp probe under spark plug type washer but not sure if its purpose was head or exhaust gas temperature .

Gary is there any specific issues with the RB twin cam heads and water cooling ?

Cheers A .

...110-115 degrees.  I would have though at this temp the coolant would start to boil?

The water doesn't boil for 2 reasons:

1. It's under pressure - pressure affects the boiling point of water. On top of Mt Everest you can't have HOT coffee because the boiling point of the water is so reduced by the low atmospheric pressure. Inversely, higher pressures RAISE the boiling point.

2. The "coolant" chemically modifies the water so it boils at a higher temperature. For the same reason, they spread salt on icy roads because the salt lowers the freezing point of water.

Basically this is why you NEVER remove the radiator cap from a hot engine - the water is likley to go "super-heated", and suddenly turn to steam.

I have pictures of an NA race RB20, and it has a big ass coolant lien at rhe back of the head, mush like you see at the front of the head/plenum???? mayeb they had worked out a cure for the temp differential? Or is that i have never paid enough attention in noticing this line on other RB engines before?

don't think this answers your question, but was talking to a race engineer and he said that they don't worry too much if there is a ~20 degree difference between water and oil... even up to 120degC on water... they run alloy heads too but I guess temp control across the head front to rear may be the key (ie. maintained temp across the head)?

All that system does is make sure that there is no air trapped in the engine. All the water lines feed upwards to for areas where localised trapped air is possible. Does NOTHING for improved water circulation.

;) cheers :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...