Jump to content
SAU Community

Recommended Posts

Car is gone so I need to sell some left over parts.

1. Apexi Injectors 440cc for R34 GTT only (Brand New) -> 700

2. Grex Oil Cooler with oil moval kit (used) -> 500 FIRM

3. Stock Clutch and stock flywheel -> 65

4. C's Short Shifter used -> sold

5. Stock Air Box with K&N Filter including snorkel (won't separate) -> sold

Pics will be provided after I get back :) Looking for buyer now

Erik

Link to comment
https://www.sau.com.au/forums/topic/103901-misc-aftermarket-parts-for-r34-gtt/
Share on other sites

  • 2 weeks later...
really need to sell them :D located in Perth.

Need some cash for my next project :(

hey mate what size is the oil cooler, and what size lines? -10 or -12? where was it mounted in the car? drivers side of front bar?

braided lines?

any pics?

Brad

I'm not too sure of the size, I didn't really measure it but it has either 11 or 12 rows.

It was mounted on my r34 gtt behind the radiator, with braided lines yes, earls lines.

I got no pics but I will be back in 2 days, I'll have the picture by then.

It's blue in colour

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...