Jump to content
SAU Community

Recommended Posts

I know there is one for sale in top notch condition, from what ive seen of it. Met the owner just today.

Give flames fitness in Lynham a call in the morning, ask for warren.

He's supposed to be selling it very soon so you may be able to get it if you call them as soon as you read this.

You can pick up a few if you shop around

http://www.carpoint.com.au/DesktopDefault....lias=carpointau

Also i have managed to get this as well. Some very nice examples in there i know compliance is on top but still

http://www.j-spec.com.au/list/auction.php?chassis=BNR34

i will dig up a few more examples but around $65 - 70 you can get a nice one kms might just be a little higher

Would you really want any R34 GTR setting for $65,000?

Remember, you get what you pay for.

Funny so many of you's have put your cars up here for sale..

Whats goin on?

Altho, id love to do the same..

Dayne, Whats with the REX pic.. Traitor! :D

I think people have had their lines long enough for an upgrade to a newer model or a more superior type of car

Also the word YOU is singular and plural, you don't need to put an S on it.

Remember, you get what you pay for.

Funny so many of you's have put your cars up here for sale..

Whats goin on?

Altho, id love to do the same..

Dayne, Whats with the REX pic.. Traitor! :D

Hahaha, sorry man:P after going in my mates STi it was just to tempting! I shopped around for some r32/r33 gtst's but i couldnt really find what i was looking for... this my98 wrx came up at a very good price, and had service history, the lot B) so i couldnt resist :P don't worry though, skylines still have their place in my heart :lol:

Dayne

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...