Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

ill take the driver side window control thing ill give u 35 buck if you post it to canberra call me on 0432453535 thanks

Mate I sent a sms to the number above...

sold now, sorry

32 tail lights gun metal grey L & R perfect condition SOLD

32 GTR front indicators L & R orange perfect SOLD

32 GTR Bonnet (Gun metal grey) SOLD

32 GTR ABS SOLD

32 glove box $30

32 GTR rear spoiler $175

32 GTR standard cooler piping SOLD

32 GTR speedo cluster $145

32 GTR centre guages $90

32 sun visors $35 pr

32 GTR windscreen wipers $30 pr

32 GTR windscreen wiper motor $40

32 GTR windscreen washer bottle with two motors $40

HKS air filters(2) with attachments that have sensors(suit GTR) SOLD

32 driver side electric window control SOLD

32 GTR oil catch can SOLD

32 GTR engine bay fuse cover $10

32 plastic piece that sits under the steering wheel, with driver side a/c vent $35

pm me for more details

located in sydney

parts not needed

for pics please send email ([email protected])

REASONABLE OFFERS WILL NOT BE REFUSED

Willing to sell everything left for $500 the lot!

Great for spares to keep around!

will a GTR speedo cluster fit a gtst and does everything in the cluster work ie, the bit the speedo cable plugs into is cracked?

Not sure if its a straigt swap fit wires maybe different, I know it will fit though.

You''ll need the centre guages as well for your boost as GTR clusters dont have them on the there.

Everything works 100%, its in perfect condition...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...