Jump to content
SAU Community

Recommended Posts

  • Replies 156
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

You beat me, oh well, lucky i think i may have found an alternative to buying Stagea specific indicators.... will test fit some S14 indicators some time in the near future.

Otherwise, friend in japan it is!

are you talking bout side or front indicators alex??

as l trial fitted a set of side indicators (as in the guard ones) from a pulsar and they pretty much fit fine, am going to have a chat with OZEparts first and see what else they have. Only problem with the pulsar one's is they are an extremely tight fit and take a bit of "persuasion" to get them in.

the guard ones are from R34/Maxima also, i'm using R34 ones on my car

Yup there the same ... as to for 200sx's.

Its strange, as knowing what nissan are like basically all parts they use on cars crossover to other cars, but atm l can't think of another nissan that has the same front indicators as the stagea does.

  • 6 months later...
  • 4 months later...
Well i got my new lights on today. i tell you what they're a bit of a bitch for the middle ones to get off. also the plugs didn't match, so i butchered my old lights loom and put them into the new lenses. they all work fine now. My old lights are for sale in the classified section if anyone is interested

NewLights.jpg

Hi mate (Terminal or anyone with advice) - I'm halfway through fitting a set of series 2 rears to mine - got the corners on no problem - removed all the trim from the hatch and undone the nuts holding on the centre lights. Are they bonded on with something 'cause I'm struggling to get the buggers off? I don't want to break anything obviously and could do with some tips on getting these off damage free. Cheers :laugh: .

Yeah they have really sticky black adhesive. i got a screwdriver under them and levered them off. it's gross stuff and gets everywhere, but as long as you have all the bolts undone it will come off with some persuasion.

Hi mate (Terminal or anyone with advice) - I'm halfway through fitting a set of series 2 rears to mine -

was wondering where you picked the set of taillights up from cos i am chasing a set to replace my cracked ones????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...