Jump to content
SAU Community

Recommended Posts

Ok, now everyone says that N/A needs backpressure and stuff and i've been doing some testing with my exhaust and my car.

Basically i have a STOCK R34 25 GT (non turbo)

with the exhaust from factory i have a very nice torque for 2k-4k which then drops

but after i modified the exhaust to bigger and more free flowing

i LOST that down low torque, however gained alot more from 4k-redline.

Im just thinking if i could basically run 1 stock exhaust and then have a flap to a 2nd exhaust with the same diametre, and have a flap open as i hit 4k. so down low, i have the low torque. but if im doing some foot to floor driving, i get the higher range or torque.

sound good? (also should help put this debate of backpressure to rest)

(more power without back pressure, however thats only at redline/high revs.. to an extent of course)

Link to comment
https://www.sau.com.au/forums/topic/104740-exhaust-mod-idea/
Share on other sites

just to clarify someone explained to me quite a while ago here in SAU that its not backpressure, but infact volumetric vacuum.

my R33 has something similar with the stock exhaust - basically has a flap with a pulley set up and opens up around 3500-4000rpm

you can hear the thing rattle a bit too..

http://www.hks-hokkaido.co.jp/movie/muffle...hipower_sky.avi

i think this is what ant95GTR is talking about (correct me if i'm wrong)

i reckon this has more to do with silencing than low rpm torque - sounds tough as though!!!!

eug

There are a couple of OEMs (Aston Martin is doing it on a couple of their cars in their range these days, off the top of my head) that do something like this.

At a certain RPM a valve opens in the exhaust, providing more flow up top. I don't know if it just bypasses the centre muffler or if it opens a completely separate set of pipes, but either way the Vanquish and V8 Vantage get a whole bunch of noise high in the rev range.

I'm considering doing something similar in my car if I ever replace the exhaust again. I was going to set up a bypass valve to route gasses around the centre mufflers at high RPM. I'd have it automatically controlled (say at a certain RPM above a certain speed. So on a stationary noise test or in first, and perhaps second, gear it wouldn't open at all) but with a manual override for when I hit the track.

sound similar yes, if its turbo u hear the turbo spool which alters the sound of the engine quite abit, but if u have an ear for it you can still tell its a skyline :P

but no WRX have the distinctive noise because its a boxer engine.

Yea.. my stock exhaust had that flap thing.. I remember when i bought it I was checking out the exhaust going.. ok someone riced my exhaust and only one is open...

Meh it sounded like crap and looked like crap tho...

As seen below..It's actually a pretty cool shot, except my new exhaust looks alot nicer.. no pics of it atm though because, my car is in repair.. Wet roads and my stupidity... :(

oidmqv.jpg

but no WRX have the distinctive noise because its a boxer engine.

Not exactly, as lingering soul pointed out.

The "boxer throb" you get from Subies is because of the crap design of the exhaust, which is forced upon them by the crap design of the engine. I could just as easily make any sound like that. The difference is that its a packaging requirement on a turbo boxer 4, and stupidity on any other kind of engine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...