Jump to content
SAU Community

Recommended Posts

Hi Guys

I did a seach on this and came up with nothing. My 89' GTS-4 has an auto transmission. It runs very smooth but doesn't want to shift into 4th (Overdrive). It will sometimes shift into 4th but then after awhile it will shift back out for no reason. I ran the Auto Trannie Diagnostic and it came back with no errors. Anyone have any idea's or suggestions?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/104955-r32-gts-4-overdrive-issue/
Share on other sites

  • 1 month later...

i'm not good with autos, here is a list of possible problems and suggested solutions

http://autorepair.about.com/cs/troubleshoo...aa072702a_3.htm

almost every one says "check transmission fluid level" so i suggest that's the first thing you should do

from above website...

No 3-4 Upshift

1. Improper band/clutch application pressure.

2. Main control assembly gaskets damaged or bolt out of torque.

3. Main control separator plate damaged.

4. Main control solenoid stuck or damaged.

5. Overdrive planet assembly damaged.

6. Overdrive band adjustment incorrect.

7. Overdrive band friction elements burnt or missing.

8. Overdrive band cylinder damaged.

good luck mate..... :P

the above website also suggests before writing your transmissino off as a rebuild first replace the fluid and filter, make sure you use correct type of fluid.

Edited by MerlinTheHapyPig

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...