Jump to content
SAU Community

Recommended Posts

  • Replies 147
  • Created
  • Last Reply

Top Posters In This Topic

R31Nismoid

If you want i can swing past a give you a ride, and if you feel more comfortable you can jump in someone elses car at one of the meeting points. I am picking up one other friend, who lives in Gladstone Park (walking distance from the s/c), so it will be no real trouble. PM me if you need a ride.

Are you guy's expecting any non Skyline owners turning up at Geelong, like /shiver/ commonwhores?

It's just that at my mates work yesterday, apparently a few non-skyliners mentioned the GOR cruise and were thinking about coming along.

Also mentioned that last time SAU came to Geelong (news to me) there was some pretty loose driving happening, so these people might be turning up expecting the same?

Just news along the grape vine, or a bad case of chinese whispers:)

Oh and for a better map of where we should meet up at the gardens, pm me with your email address.

AL,

i'm right for a lift mate... DJ is picking me up fomr my place (tulla) at around 8.30.

You can meet us there if you like ?

PM me for my address.

Interloper....

if word has got out (not that it matters) good luck to them.

if they behave like idiots and do things that might attract unwanted attenetion (cops) we'll tell them to move along.

But remember... there are other cruises with other clubs that day also, maybe they are talking about that?

R31Nismoid

NO worries bud, we are all here to help each other.

If i see a couple of skylines in Tulla i will join you there, otherwise we can meet up at macca's on the ringroad at 9am

See ya then.

If you see this car in Tulla. give us a yell, just in case i am still half asleep :P .

Guest Señor Deanodriver
Originally posted by Interloper

Are you guy's expecting any non Skyline owners turning up at Geelong, like /shiver/ commonwhores?

what about Pintaras? :P

I may rock up for a looksie (no stupid shit though), cos I like Skylines, and because it's about 20 minutes away, so if ya see a trashed silver R31 Pintara wagon with P plates on it, it's probably gonna be me :D




  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...