Jump to content
SAU Community

Miswc Gtr Bits For Sale

GTR090
 Share

Recommended Posts

GTR090 Rising Star

GTR090

Posted
Posted (edited)

Hey guys, got some more parts for sale....

Gear box - $650 SOLD

Front hubs - $100

Front k frame - $200

Front left quater panel -$150 SOLD

Rear half cut - $500

Boot lid(with GTR badge) -$150

Rear bumber bar - $150

Rear lights - $100

Doors(both mint condition) gun metal grey- $400

Side view mirors. gun metal grey - $50

Centre guages -$40

Starter motor - $150

Rear drive shaft - $100 (each)

Window controls on driver side - $40

Speedo cluster(standard) - $ 50

Reasonable offers welcome.....

0416 255 683

Edited by GTR090
Link to comment
https://www.sau.com.au/forums/topic/105046-miswc-gtr-bits-for-sale/
Share on other sites
racer_boy Rookie

racer_boy

Posted
Posted

Where was the floor and roof of the car cut in for the rear cut? When the car copped the hit in the front did it move or kink the roof in any way? Whereabouts are you, I'm keen to see the rear cut right away, I'll PM you my mobile number so we can fix a time for this.

Beer Baron Grand Master

Beer Baron

Posted
Posted

what colour was the car?

the boot lid: what condtion is the paint on it? also does it just have the standard GTR wing holes? ie no extra holes, and no marks from N1 lip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • wizlb
      Flex Fuel Kit Workshop

      By wizlb · Posted

      Thanks Dose.....    I appreciate it!!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • Piggaz
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By Piggaz · Posted

      I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...