Jump to content
SAU Community

Recommended Posts

hey guys,

I recently noticed right at the front of my gear box where it connects to the engine there is an oil leak near one of the bolts. But its a very slow leak, like after a week in the garage there is a very small patch on the floor. Can someone tell me why it would be leaking there?? Does it need to be tightened more? or too much oil or is something broken? Just wanna know how urgent this will need to be fixed.

I have attached a pic of where it is leaking and circled it. post-23859-1139730510.jpg

Thanks for the help

:P

Link to comment
https://www.sau.com.au/forums/topic/105536-front-of-gear-box-leak/
Share on other sites

It might be the rear main seal, but there appears to be oil staining on the sump further forward in that photo and it might be that the oil is just collecting at the lowest point. Before going to the trouble and expense of removing the gearbox, I suggest you _thoroughly_ degrease the entire area, run the car for a week or so and see if you can confirm where the leak is.

As suggested.. It could just be the sump pan bolts. I've tightened them on another car, and thats been enough to fix the leak. They often work loose over time.

If you're unfortunate, its the rear main seal, which means the whole gearbox (and flywheel) has to be taken off to replace the seal.

It seems to a common problem in older RB engines. My rb20 has had the same problem for quite a while.

defently do a degrease and see exactly where it coming from from.

if you do have to change the seal, the oem ones cost about $80!! i went for an aftermarket which looked exactly the same and cost me $20.

no probs so far (touch wood)

steve

Thanks can you let me know where you got your seal from for 20 bucks?? :P

GRRRRRRR did'nt think of the rear main seal but that's prob what my prob is too. Looking at your pic, it's similar to my issue. It does'nt leak like a sive but when I push the car hard I notice a little puddle and it drips from the lowest point which would be the bell housing of the tranny.

Crap....NOW IM PISSED! :(

I will go through and check that all my bolts are tight but other then the head gasket or rear main seal there really is'nt any other place it could come from. Funny thing is my oil level has'nt really changed at all. :lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...