Jump to content
SAU Community

Recommended Posts

As per title really.

We got a RB26 to go in a R33GTR here, and its been bench dyno'd running Pectel T6 2000 managment and its now in the car, but not running as yet due to a few mods being done.

But what (if any) effects will not running the standard ECU and engine loom have on the 4wd system?

I thought it was a totally seperate entity with the ATTESSA ECU doing it all, so no effects when binning the standard ECU, but some say otherwise.

So whats the truth? And if there are changes, what mods needs to be done to make it work ok?

Cheers.

Stav

There are shared sensor inputs or signals between the ATTESSA and ECU computers. I know for a fact that TPS is one such signal as I had some issues ATTESSA a while back when I was running a single throttle body.

Study the electrical line diagrams from the manual and you will see what I mean.

ATTESSA needs a TPS signal, otherwise it goes into "error" mode.

Advanced Engine Management (Wolf 3D) has a "black box" add-on to provide the signal to the ATTESSA.

EASY MATE. the only wires needed to keep the atessa working is:

tacho (pin 7)

tps signal (pin 38)

need to splice this wire 56 (purple one) into pin 38 as most aftermarket ecus dont have a tps output for other things.

should take about 2 mins to do :)

cheeres :lol:

ps.. make sure you adjust the tps with the engine running to get .04 volts at the output (tps signal input) otherwise code 21 will pop up...

off topic a little bit sorry, but does anyone know if u can hook up the front torque gauge from a gtr onto a stagea series 1 which i dont know if it has the pin out of the attessa ecu or not?

ive got the tps signal hooked up and the tacho so it should work as per normal without the engine ecu and using an autronics smc?

is their anyway of telling if its working correctly without the front torque gauge?

cheers

Brad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
×
×
  • Create New...