Jump to content
SAU Community

Recommended Posts

Hey everyone.

Im currently in the middle of modifying my R33 GTST

Top mount manifold

TO4e Turbo

40mm external wastegate

Apexi Power FC with HC

Front mount (600x300x76)

K&N 3" Pod

Bosch 040

Apexi AVCR

Sard Fuel Pressure Reg

Hi Flowed injectors

Upgraded spark plugs

Front facing Plenum

XF Throttle Body

Mandrell Bent 3" Custom cooler piping

Z32 AFM

Oil catch can

HKS SSQV Bov

I'll be on a full licence when its back on the road

How f@#ked over will i be if a cop pulls me over or if i get sent to epa

wat will happen

Is there anything i can do to legalise it

Engineers certificate???

Need Advice fast lol

Thanks for any help u can give.

Cheers

Guesty

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/
Share on other sites

Dont bother with an engineers certificate as it says on the bottom in huge writing "Valid For Only 30 Days After Inspection Date"

Dont think you can legalize it due to the fact that the turbo and everything else helps to increase your emisions.

The engineers certificate is good for proving structural changes in your car are safe and legal.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963645
Share on other sites

nothing you can do

with a highmount (and a crappy one at that ;)) your 100% f*cked

External Gate - 100% farked

modded plenum/Throttle Body - 100% farked

If i were you, i'd be very careful when/where/how you drive it

If they catch you.

You have to return it to 100% stock.

STOCK everything right down to the injectors and fuel reg :(

Pray to the gods is all you can do on that one

Engineers does not cover EPA in any form.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963690
Share on other sites

If they catch you.

You have to return it to 100% stock.

STOCK everything right down to the injectors and fuel reg :)

Pray to the gods is all you can do on that one

Engineers does not cover EPA in any form.

Hey Ash

Is putting in bigger injectors, and an aftermarket fuel reg defectable?

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963743
Share on other sites

I know someone with a very similiar setup who was once pulled over by a cop and asked to pop the bonnet and the cops didnt say anything as they looked very confused at what they were looking at in there. :(

Guesty if your gonna do this setup then I would get another car an a daily driver coz u r sure to get done if driven around everyday.

Dark most cops aint gonna pick aftermarket injectors or fuel pres regs easily.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1964863
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...