Jump to content
SAU Community

Recommended Posts

Hey everyone.

Im currently in the middle of modifying my R33 GTST

Top mount manifold

TO4e Turbo

40mm external wastegate

Apexi Power FC with HC

Front mount (600x300x76)

K&N 3" Pod

Bosch 040

Apexi AVCR

Sard Fuel Pressure Reg

Hi Flowed injectors

Upgraded spark plugs

Front facing Plenum

XF Throttle Body

Mandrell Bent 3" Custom cooler piping

Z32 AFM

Oil catch can

HKS SSQV Bov

I'll be on a full licence when its back on the road

How f@#ked over will i be if a cop pulls me over or if i get sent to epa

wat will happen

Is there anything i can do to legalise it

Engineers certificate???

Need Advice fast lol

Thanks for any help u can give.

Cheers

Guesty

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/
Share on other sites

Dont bother with an engineers certificate as it says on the bottom in huge writing "Valid For Only 30 Days After Inspection Date"

Dont think you can legalize it due to the fact that the turbo and everything else helps to increase your emisions.

The engineers certificate is good for proving structural changes in your car are safe and legal.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963645
Share on other sites

nothing you can do

with a highmount (and a crappy one at that ;)) your 100% f*cked

External Gate - 100% farked

modded plenum/Throttle Body - 100% farked

If i were you, i'd be very careful when/where/how you drive it

If they catch you.

You have to return it to 100% stock.

STOCK everything right down to the injectors and fuel reg :(

Pray to the gods is all you can do on that one

Engineers does not cover EPA in any form.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963690
Share on other sites

If they catch you.

You have to return it to 100% stock.

STOCK everything right down to the injectors and fuel reg :)

Pray to the gods is all you can do on that one

Engineers does not cover EPA in any form.

Hey Ash

Is putting in bigger injectors, and an aftermarket fuel reg defectable?

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1963743
Share on other sites

I know someone with a very similiar setup who was once pulled over by a cop and asked to pop the bonnet and the cops didnt say anything as they looked very confused at what they were looking at in there. :(

Guesty if your gonna do this setup then I would get another car an a daily driver coz u r sure to get done if driven around everyday.

Dark most cops aint gonna pick aftermarket injectors or fuel pres regs easily.

Link to comment
https://www.sau.com.au/forums/topic/106481-wat-2-do/#findComment-1964863
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...