Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yes i have an aftermarket gtr front bumper and i had to trim it for the piping to fit

and the only hole needs to be cut is under the battery , you can see an imprint of a 3" hole just use that as a guide i cut that hole bit out

and on the other side where it used to have 2 pipes going to the stock intercooler i cut that bit open so its nice and wide and you can manouver the pipes

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2289912
Share on other sites

ok the only thing i got now is to do the hole on the side to fit the last pipe. just a question is your intercooler on a angle?? like the top sticks out and at the bottom in comes in. if you know what i mean.

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2290084
Share on other sites

yes the intercooler sits on an angle, well mine does anyway and everyones i seen it sits on a angle, like the bottom is closer to the car and the top sits further away

the brackets at the bottom i got with my intercooler kit, they just need to be screwed to the chassis at the bottom..

and at the top i made a plate

both top bolts screw into the fmic and then you get a plate which holds them both togethor, then another one in the middle of the two which can bolt up to a bolt near the bonnet latch you will see it..

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2290127
Share on other sites

Hey dude just go to Mettams exhaust and tell them you want a 3inch System from the turbo back (down/dump pipe, high flow cat , the works.) and you can choose a nice cannon style muffler or watever you want on the end. They did a killer job on my R33 for $1100.My car basically went from not much wheel spin in the dry to BLAZING and it doesn't hang down like them ricer jobs and isn't going to atract the cops with excessive decibels.

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2296455
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...