Jump to content
SAU Community

Recommended Posts

Tell me about it. I got an email today saying funds have cleared, and are being shipped, so i wont expect them to be hear till monday if thats the case.

so do you have them today?

:D

  • Replies 181
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Nope, and im not frikking happy either. Ive paid for overnight courier to me (at my expense) and they still havent arrived. Ive spoken to them just them, and explained im not happy at all, as ive paid, and been told these would ship thursday last week.

Ill keep u informed....

I HAVE THE BUSHES!!!!!!

miracles do happen. :O

Ok guys, im packaging these up and sending them out, so it may take me a day or so to get them all done and out (ive got a dozen here to do). Hope u all get a nice suprise soon :P

Thanks for taking part in the GB, and NO im not doing another :(

Just looking at them, and they are definitly smaller than the r33 bushes as well for those who are wondering, so fitment may be easier.

Edited by Bl4cK32

Can all u guys who havent sent me a pm with your address please feel free to do so. Ive got a couple already, and i dont know how to sent out a multiple message to the 10 other guys.

So if u havent yet, please do so....

I sent two lots out. I asked a member of my family to send out the second lot as ive got a bad back (disc problems) and foud it hard to get to the post office. I found that the second lot was only posted today, so dont worry everyone should have them by monday at the latest...

GTR1993 i can drop yours off as im in Adelaide, but the other side of town. If im going past on the weekend i can stop by, or monday at the latest. Pm me when someone will be home either sat or monday with a mobile number -

thanks guys.

Ps - if no-one has seen them by wednesday, lemme know and ill contact the post office to find out whats going on

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...