Jump to content
SAU Community

Intercooler With Inlet And Outlet On Same Side

Johnny Cash

By Johnny Cash,
in Engines & Forced Induction

 Share

Recommended Posts

Johnny Cash Experienced

Johnny Cash

Posted
Posted

Hey fellas,

Just tapping into your brains again for some intercooler advice.

I've noticed most of the hybrid and copy kits have the pipe on the right hand side that goes half way over the engine and into the inlet manifold.

I was just wondering if an intercooler with inlet and outlet on the same side would be better on a GTS-T, as it would involve a lot less piping. Would theoretically have two benefits - less pipe (less lag), and no piping going over the engine (as opposed to traditional intercoolers with inlet and outlet on opposing sides).

Obviously on GT-Rs, you're better off with the traditional style cooler, but I figured with a GTS-T it would be a different story.

There's one on eBay that caught my attention:

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...AMEWA%3AIT&rd=1

I'm thinking that's the way to go, but want your opinions.

Thanks again,

J.R.

Busky2k Veteran

Busky2k

Posted
Posted

My bet it would be pretty restrictive despite their claims, and the cold outlet is right next to the hot inlet (and same goes for the core) so I'd be questioning its cooling efficacy. So just go with the tried and tested in/out on opposite ends..

BHDave Grand Master

BHDave

Posted
Posted

the end tank design on the far end doesn't look the best for flow and the top pipe will end up pointing straight at the mount for your front bar reo.

I noticed they had an apexi looking core with a crossove type outlet which would be considerably better flowing but the down side is that you end up with 2 feet of extra piping compared to the regular across the top of the radiator method.

RANDY Veteran

RANDY

Posted
Posted

There is some HKS cooler that uses your existing piping-holes on the right-hand side. The cooler comes with the rest of the piping, which includes a 180 degree turn. The return outlet on the left of the cooler turns around and travels below the core, back to the factory holes for piping.

The bend isn't terribly nice to have, but you don't need to hack your left-hand side to run pipes in and over your fan, and the cooler forces the air to travel the whole intercooler.

SKY 34 Mentor

SKY 34

Posted
Posted (edited)
My bet it would be pretty restrictive despite their claims, and the cold outlet is right next to the hot inlet (and same goes for the core) so I'd be questioning its cooling efficacy. So just go with the tried and tested in/out on opposite ends..

I agree with the cooling efficiency bit...I dun think it'll work as well at all....dunno if this is right..but..

I'm thinking if air were to enter from the bottom pipe (hot air rises?), it does not necessarily travel to the other end of the intercooler to get cooled and back again to go out from the top pipe...the air can just flow straigh from inlet up to the outlet...

Edited by SKY 34
Johnny Cash Experienced

Johnny Cash

Posted
  • Author
Posted

Yeah, I think you're right SKY34, will have to go a conventional intercooler.

But I'm just wondering if the extra cooling you get from running a 'normal' ic is combatted by the ic pipe that has to run all the way over and around the engine to go to the intake manifold...

Just a thought.

hey Michael, can you send me the link for that?

How much, and who do I pay?

Kaido_RR Grand Master

Kaido_RR

Posted
Posted

here is the link: http://page6.auctions.yahoo.co.jp/jp/auction/f42804965

best bet is to contact- SAU Trader Slidewize Imports (as Zac buy stuff off yahooauction)

at the current price its 22,000yen (about $260 + shipping and other fees)

silva33 Mentor

silva33

Posted
Posted

I have a trust cooler as pictured above and highly recommend them! I am making decent power 244rwkw and the cooler is not a restriction at all... they are not as big as the hybrid coolers but it all comes down to how much power you want to make...

The best thing about it is that the engine bay looks stock...

Johnny Cash Experienced

Johnny Cash

Posted
  • Author
Posted

Thanks mate, will do.

Lovin that cooler, says its for R31 RB20DET? Should that make a difference?

Either way, if I can get it to my door for around 300, it would definitely be worth it.

Even tho I'm broke :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...