Jump to content
SAU Community

Recommended Posts

Does anyone know if the washer looking thing inside one of the hoses that goes to the intercooler piping from the wastegate that has a red line marked on it is a boost restrictor thingo or does it help to increase boost etc.

figure that out and then get back to me

RiaZ

Link to comment
https://www.sau.com.au/forums/topic/10730-boost-restrictor-thingo/
Share on other sites

well i was talking to gav with an r32 gtr and he said it did increase but he was also saying on the s platform s13, 14, 15 you need to put a bigger restriction in to get higher boost.

so cos i dont have a boost guage i am using the factory r33 one, yeah i know its shocking well it has a 0 and a +7 marked and when i took the restriction out it climbed to the mark that is between those two so basically 3.5 but when i put the thing back in it went to between the 3.5 and the 7. now it seems obvious that it is producing more boost but the seat of the pants story is different. the car doesnt seem to have that 2 stage factory boost like normal it just gets to the 3.5 and sits there rock steady

someone enlighten me

I can check again when i get a boost guage but if someone has a guage how about you go out right now and pull that thing outta there and come back and let me know

RiaZ

the bleed valve install is a 'no-brainer' (that's why I could do it).

It plumbs staight in with no fuss. Adjust it slowly a notch at a time and give it a bootfull on the freeway in 4th. In fact the freeway is a great place to do the tune. There is no need to exceed the limit as the turbo under load in 4th will get to max boost well before you break the law.

leave it at 10psi and I'm sure you will be more pleased.

what are you guys talking about now.... what is the deal with the restrictor thingo, cmon,

i got a bleed , forget me installing it. I wanna find out if the restrictor is better not there or if it is not a restrictor as such??

something like that

oh and yes the bleed will be going in shortly. i wanna get the dump pipe sorted first and the boost gauge

"not very good with non-stock turbo's though"

id have to disagree there paul. i run a bleeder on my turbo and its flawless. holds 15psi no worries. no spiking and builds smoothly, couldnt ask for anything else. from my experience with a GFB bleed valve theres much better things to spend money on then an EBC (which are quite pricey)

i understand u dont see the top secret supra getting around with a turbosmart bleed valve but for most of our cars bleed valves are decent

Most other people experience spiking with there bleed valves, they aren't designed to compensate for the change in boost levels like an EBC, but some people like them. I used one for a while, didn't like it, but that's my situation.

Non-stock turbo's tend to produce alot more airflow, and the bleed valve doesn't react too well.

See'ya:burnout:

Yeah, external wastegates are a major improvement for proper control. I will have one oneday, but until then I'll keep my EBC, it works nicely, plus has the advantage of being able to change boost in cabin, but agreed they are too expensive.

See'ya:burnout:

bleeder are a poor mans EBC and don't do anywhere near as good a job bringing the boost on quick or holding boost.

If you have the money an ebc is great stock turbo or not. If I had one my times over the quarter would be a tenth or two lower just from the extra response they offer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...