Jump to content
SAU Community

Recommended Posts

Hi guys,

Gonna try to track down some R-compound tyres for the next hillclimb and future trackdays... was just wondering if anyone had any feedback about good/bad places to buy them from in Brisbane?

At this point (after searching) it's coming down to the Dunlop D01J or DZ02G, or Bridgestone RE55, or maybe some Yokos. I know you can pick up the Dunlops from Qld Raceway but just wanted to hear people's experiences etc.

The sizes I'm after are front: 235/45R17 and rear: 255/40R17 (or maybe 265/40).

Also I have no idea what compound to go for - the tyres will be doing the Mt Cotton hillclimb and trackdays at QR only (5 lap stints), I don't plan to use them on the street except to drive there and back.

Thanks :P

Link to comment
https://www.sau.com.au/forums/topic/107421-buying-semi-slick-tyres-in-brisbane/
Share on other sites

I've bought D02G's from Qld Raceway before - no problems at all. Previously ran the Bridgestone RE55's which I think (in my opinion only) may be a slightly superior. Bridgestones you can buy from Tyretech.

If you wanted a tyre specifically for hillclimbs, I would look at the Toyo Proxes (R compound) available at plenty of places (bought mine at Keith 4 wheels) Extraordinarily good in short sprint events. At QR, they start to go off by about lap 3 or 4 and become too "squidgy" but would be superb for hillclimbs.

Edited by maccattack

I got Dunlop DO1J on my street car, they're dot rated and I have been quizz in the past by the officers of the law, just point it out to them, that's all. I think D01j comes in 3 compounds soft/super soft/ chewing gum. just get the soft/or medium, as the chewing gum one only last about 1500-2000k on the street and alot less on the track. Very nice tyres , with plenty of grip/warning.

Cost to KMs, and wet weather would be two of the big ones.

Wet weather is no probs for semi's. It's the rubber compound, not the grooves that keep you stuck to the road. I've run semi's in the wet before with great traction. But you're right - cost per km is the killer.

Wet weather is no probs for semi's. It's the rubber compound, not the grooves that keep you stuck to the road. I've run semi's in the wet before with great traction. But you're right - cost per km is the killer.

Id debat the thing with the wet weather. I guess it would depend on the tread patter to some extent. Some cars I have been in with them on, bit of rain, bloody hell, never again.

Ive just fitted 235 and 255 on my GTR Falken Azenis RT215-fine in the rain last night(I have over 400hp at wheels)-they are DOT approved and George at Tyrepower at Albion did them cheap as and got them in one day.

Ive just fitted 235 and 255 on my GTR Falken Azenis RT215-fine in the rain last night(I have over 400hp at wheels)-they are DOT approved and George at Tyrepower at Albion did them cheap as and got them in one day.

Can I ask how muck "cheap as" is?

They were 18" right ???

No sorry 17's cause mine is a 32GTR-one key to light weight is going 17in -less unsprung weight unless youve got super lightweight 18in rims(then there can be strength issues)

$1300 fitted and balanced-He even lowered my coil overs to suit for nothing-best people to deal with.

Others in Bris were quoting over $1400 without fitting

Edited by overev1

the Azenis RT215 really isn't an R compound tyre. far too hard and lacks the outright grip of a true R compound. Better than a normal street tyre though and probably not a bad choice if you only have one set of rims, because they'll last alot longer than a proper R tyre on the street.

I've used the Azenis RT215, a Hankook Z2000 race tyre, Yoko A032R, and Bridgestone RE55S. The Azenis are about 1.5 to 2 sec slower at Mt Cotton than the proper R tyres.

Talk to Craig at Hornibrook Tyres. He's the cheapest around for motorsport tyres, and he'll look after club motorsport competitors because he is one himself! He's a regular at Mt Cotton and motorkhanas etc. Tell him Harry put you onto him.

5 Basalt Street,

Geebung QLD 4030

Phone 3865 1072

Mobile 0401 474 745

Wet weather is no probs for semi's. It's the rubber compound, not the grooves that keep you stuck to the road.

That is actually incorrect. The compound keeps you stuck to the road in the dry...the only thing the grooves are designed for is wet weather traction.

That is why drag tyres have no grooves, they don't race in the wet.

Probably it would be right to say that the grooves pump the water out in the wet so the tyre can make contact with the road. The compound is softer on R-Compound tyres so they do stick better in the wet. That's why wet weather tyres perrish in racing when the track drys out.

Talk to Craig at Hornibrook Tyres. He's the cheapest around for motorsport tyres, and he'll look after club motorsport competitors because he is one himself! He's a regular at Mt Cotton and motorkhanas etc. Tell him Harry put you onto him.

5 Basalt Street,

Geebung QLD 4030

Phone 3865 1072

Mobile 0401 474 745

I second this, just bought a full set from Craig, top bloke & good prices.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...