Jump to content
SAU Community

Recommended Posts

R33 Factory Wheels (16") ....You guys know what car's they'll fit and what they wont..good for a back up set, or go halvies with a mate and have some burnout wheels...They have tyres on them, but they are not roadworthy.....i ripped them up before i got my rims..hehehe..

Like the wheels below

$265 Or Nearest Offer

2.jpg

Link to comment
https://www.sau.com.au/forums/topic/1076-r33-factory-wheels/
Share on other sites

Put me down for two of them, if anyone else will go halvies and take the other two that is? Remember a 16" tyre will flex more than a 17" and offer better traction at the drag strip, with a good tyre of course.

Link to comment
https://www.sau.com.au/forums/topic/1076-r33-factory-wheels/#findComment-23695
Share on other sites

Hehehe for $265 each rim you could nearly get a set of 18's witho ut tyres! heheh..

Nah man, its for the set....If you want em, take em...let me know via here or phone 0421 34 1981...Centre Caps included (they are damn hard to get these days!)

Regards

Sam

Link to comment
https://www.sau.com.au/forums/topic/1076-r33-factory-wheels/#findComment-23799
Share on other sites

I'm assuming the reason you go halves is just to run them on the rears with large profile tyres for dragging ? I was after them for a set for when I get defected, but I'd be happy to go halves, I will have to wait until next Friday though to deposit the $$$ due to pay week, but once again I'm more than happy to go ahead, just have to wait a week ...

Link to comment
https://www.sau.com.au/forums/topic/1076-r33-factory-wheels/#findComment-23923
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...