Jump to content
SAU Community

Recommended Posts

  • Replies 106
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Any one know the amount of colour coats and then clear coats on the GMG R32 GTR out of the factory? I know the colour is Nissan's KH2, but I have a body kit in mind and want it fitted after spraying and also want the bonnet resprayed to match the cars exact colour.

Also, what would it cost to get a kit + bonnet resprayed? I will probably take my car to damage control because I have some rust that I want them to clean up for me as well.

Link to comment
https://www.sau.com.au/forums/topic/108736-re-spray/page/5/#findComment-2317132
Share on other sites

  • 1 month later...

5500 it is going to cost me to get my car dont by fibre vision, going with black, red pearl, and gold glitter. i guess i am paying most of it by labour, cause of the colour i am after and this is just the out side of ther car

Link to comment
https://www.sau.com.au/forums/topic/108736-re-spray/page/5/#findComment-2446514
Share on other sites

thats reasonably 'cheap' for what you are having done.

not having the door seals/engine bay/etc etc done?

i was going to get mine done in calsonic/bionic blue, before i decided to sell it, was looking at about $7,000 for that, but i *know* that would have been a good job.

Link to comment
https://www.sau.com.au/forums/topic/108736-re-spray/page/5/#findComment-2446690
Share on other sites

  • 3 weeks later...

umm depending if you have had any past experiance and how confident you are. could do the prep work your self, such as getting the car primed up and everything, takes a while and your car while look funny for a while but it really cuts down man hours therefor taking a huge chunk out of the cost,

me and my mate worked on priming his hilux mini truck every weekend, took a while but that was because we were shaving door handles etc.

it is time consuming but the longer you take to get the primer on there right and sanding it back so its 100 percent perfect the better finish you will get.

this is my mates car preped and when he got it sprayed >_< hope this helps, if it doesnt then shoot me >_<

post-24878-1158321646.jpg

post-24878-1158321688.jpg

Link to comment
https://www.sau.com.au/forums/topic/108736-re-spray/page/5/#findComment-2500336
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...