Jump to content
SAU Community

Recommended Posts

  • Replies 283
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey guys,

i will be meting up with yous at the twin servos.

I have 2 other Newcastle skylines that are coming with me.

i also have a few other cars that would like to come they are;

FTO x2

600HP Supra

Honda Integra

Is that cool?

do you a deall.. we'll take the skylines and supra, and you can keep the rest! k?

ok, so who from hornsby is meeting up at F3 freeway?

i was thinking we could meet at thornliegh maccas around 10 30 and wait for the others to drive past

who is keen?

I am!

:D

ok, so who from hornsby is meeting up at F3 freeway?

i was thinking we could meet at thornliegh maccas around 10 30 and wait for the others to drive past

who is keen?

I am!

:D

sounds good to me

hmmmm, i thinks i will meet at the twin servos (on F3 right?..north bound of course).....i think 11.30 would be a goer weapn. what do you think? 1 hr for the guys to get there from Homebush?

ok ppl 2mrw is the day, get some good sleep, wash your cars, get your bf & gf to come along, get to cameras loaded, coz this will be a day we will talk about for a lil while. lol

for all those people who are going alone, dont worry you will no me the only one....mehhh too :D

for the newi ppl, if things go as planned we should be at the twin servo hopefully by 12:30pm, please leave some space for us, there maybe over 50cars 2mrw.

for all the people who just joined SAU, you guys can register to be a member here at the site, i do not deal with this i just do cruises :)

goodluck guys, drive safely, do not put others in danger, and just remember its double demerits. I will be notifying the Newecastle Police that we are coming so they wont think we are there to start trouble. We have a good record there so please DO NOT ruin it. Goodluck and ill see u all 2mrw, nyt

Thankyou

ok, so who from hornsby is meeting up at F3 freeway?

i was thinking we could meet at thornliegh maccas around 10 30 and wait for the others to drive past

who is keen?

I am!

:D

Yeah i'll meet up at Thornleigh maccas, its major back tracking for me to head to Homiebush too...

It might be a little difficult to sorta wait for them to fly past... we would have to be sort of sitting in the side street ready to go dont you think?

Yeah i'll meet up at Thornleigh maccas, its major back tracking for me to head to Homiebush too...

It might be a little difficult to sorta wait for them to fly past... we would have to be sort of sitting in the side street ready to go dont you think?

Nah we could catch em on freeway. That many cars aren't gonna be able to stick together through lights and stuff anyway. Plus weevil said he has supermans number so we could co-ordinate it a bit

Sorry badly written, meant we could be sorta waiting in side street till they're near




  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...