Jump to content
SAU Community

Recommended Posts

hey all,

I have just had my motor replaced and have had some vacum leaks fixed and an exhaust manifold leak fixed. Before they were fixed car wasnt boosting up. Car is boosting up now but seems to be hesitating a bit. Doesnt seem to be comming on boost as hard.

I have added a front mount and i was told to expect more turbo lag, but the car feels substantially slower. I notice it quite a lot in 3rd gear, Second doesnt seem to bad. Idle goes up or down a bit every now and then too. I have noticed when the idle does this, I can hear a clicking near the front or intake side of the head just as the idle changes?

Any Ideas anyone?

And also what does everone sugest i do to treat my newly formed car? Good oil? etc

thanks

Link to comment
https://www.sau.com.au/forums/topic/109663-rb25det-acting-strange-help/
Share on other sites

I have just had my motor replaced

I have added a front mount

ummmm - has it been tuned as yet with the fmic on??? my rb25det was very hesitant when I put on the fmic, now after a tune is very strong.

The car has the following mods,

K&N pod filter

Hybrid Front Mount

3 inch cat back exhaust

Daikon/exedy brass button clutch

kyb struts and springs

I havnt had the car tuned after I have put motor in and the front mount so maybye that is the problem. I am confident it is not the usual coil, or spark plug issue as they are new and coils have been checked 2 weeks ago.

Noticed idle fluctuating between 800 and 100 rpm everynow and then again today. Almost sounded like it had lumpy cams.

James,

The engine is out of a series two 97 model, i didnt rebuild old motor as block was screwed.

I dont have a aftermarket boost guage. I also have performed that high boost mod mod that is stated on this site, possibly a dumb move befor car was tuned.

Sounds dumb and you've prob checked it anyway but it made my 33 idle fluctuate as you've described...

Right at the front of the fuel rail (cyl #1 end of motor) is the fuel pressure reg which has a little vac hose attached to it....this hose may have a leak or has come off....

Yeah ill try the ecu reset tmrw thanks for that. Yeah ill try injector clean too. Guy thinks that there may have been bigger injectors in the half cut i bought. May be something to look at, maybye they need better reg or pump?

it sounds like you are hitting the factory excess airflow protecition. this is usually the result of an incorrectly plumbed in actuator line. check there is a pressure line from the intercooler piping running to the turbocharger actuator (copper bubble with a nipple on it).

if its missing your are running unlimited boost and the ecu is protecting itself. what does the factory boost guage show? does it goto +7 ?

On that note of ECU's and motor swaps...

The series 2 motor doesn't run the ignitor on the top of it, it's run from the ECU. How did your mechanic get around this? Swap ECU's, or do something funky with another ignitor?

oh you have a series 1 ecu running a series 2 engine?

i once tried a remapped ecu and it was from a series 1 rb25

i experienced the same sorta things you mentioned, really flat gear feelings despite the car running fine.

please confirm what ecu you have and what engine (series 1 or 2)

if you have series 1 ecu on series 2 engine i would recommend buying a series 2 ecu

well if it in fact is a series 1 ecu on a series 2 rb25 engine (which seems to be the case without confirmation) then an safc will help a little but i suspect the problem will still be present or get worse. you would be better off getting a correct series 2 ecu.

the powerfc will fix it as the powerfc is the same wether its the series 1 or series 2 rb25, its the same ecu.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...