Jump to content
SAU Community

Recommended Posts

hey all,

I have just had my motor replaced and have had some vacum leaks fixed and an exhaust manifold leak fixed. Before they were fixed car wasnt boosting up. Car is boosting up now but seems to be hesitating a bit. Doesnt seem to be comming on boost as hard.

I have added a front mount and i was told to expect more turbo lag, but the car feels substantially slower. I notice it quite a lot in 3rd gear, Second doesnt seem to bad. Idle goes up or down a bit every now and then too. I have noticed when the idle does this, I can hear a clicking near the front or intake side of the head just as the idle changes?

Any Ideas anyone?

And also what does everone sugest i do to treat my newly formed car? Good oil? etc

thanks

Link to comment
https://www.sau.com.au/forums/topic/109663-rb25det-acting-strange-help/
Share on other sites

I have just had my motor replaced

I have added a front mount

ummmm - has it been tuned as yet with the fmic on??? my rb25det was very hesitant when I put on the fmic, now after a tune is very strong.

The car has the following mods,

K&N pod filter

Hybrid Front Mount

3 inch cat back exhaust

Daikon/exedy brass button clutch

kyb struts and springs

I havnt had the car tuned after I have put motor in and the front mount so maybye that is the problem. I am confident it is not the usual coil, or spark plug issue as they are new and coils have been checked 2 weeks ago.

Noticed idle fluctuating between 800 and 100 rpm everynow and then again today. Almost sounded like it had lumpy cams.

James,

The engine is out of a series two 97 model, i didnt rebuild old motor as block was screwed.

I dont have a aftermarket boost guage. I also have performed that high boost mod mod that is stated on this site, possibly a dumb move befor car was tuned.

Sounds dumb and you've prob checked it anyway but it made my 33 idle fluctuate as you've described...

Right at the front of the fuel rail (cyl #1 end of motor) is the fuel pressure reg which has a little vac hose attached to it....this hose may have a leak or has come off....

Yeah ill try the ecu reset tmrw thanks for that. Yeah ill try injector clean too. Guy thinks that there may have been bigger injectors in the half cut i bought. May be something to look at, maybye they need better reg or pump?

it sounds like you are hitting the factory excess airflow protecition. this is usually the result of an incorrectly plumbed in actuator line. check there is a pressure line from the intercooler piping running to the turbocharger actuator (copper bubble with a nipple on it).

if its missing your are running unlimited boost and the ecu is protecting itself. what does the factory boost guage show? does it goto +7 ?

On that note of ECU's and motor swaps...

The series 2 motor doesn't run the ignitor on the top of it, it's run from the ECU. How did your mechanic get around this? Swap ECU's, or do something funky with another ignitor?

oh you have a series 1 ecu running a series 2 engine?

i once tried a remapped ecu and it was from a series 1 rb25

i experienced the same sorta things you mentioned, really flat gear feelings despite the car running fine.

please confirm what ecu you have and what engine (series 1 or 2)

if you have series 1 ecu on series 2 engine i would recommend buying a series 2 ecu

well if it in fact is a series 1 ecu on a series 2 rb25 engine (which seems to be the case without confirmation) then an safc will help a little but i suspect the problem will still be present or get worse. you would be better off getting a correct series 2 ecu.

the powerfc will fix it as the powerfc is the same wether its the series 1 or series 2 rb25, its the same ecu.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...