Jump to content
SAU Community

Recommended Posts

Hi everyone.

Well my R32 GTST has had some headlight problems ever since I got it. When i first went to use my high beams after I bought it, the headlight fuse blew leaving me with no headlights at all. I replaced the fuse/s and everything seemed fine (it was dark). I've pretty much avoided any use of the high beams since, which is fine. But the headlights have always seemed very 'dim', as in not lighting up the road much at night. Since then the fuse has blown again just on normal operation of the low-beams. I replaced the fuse but noticed that the fuse (blue colour 15A) has actually melted and warped!! And there seems to be a lot of cr@p all over the fuse holder connection, which I gather may be melted plastic.

Anyone know what would cause this??? Anyone had this problem before???

Ohh and the melting only seems to happen to one headlight fuse, not the other.

Fixxxer :rolleyes:

Edited by Fixxxer
Link to comment
https://www.sau.com.au/forums/topic/109673-headlight-issues/
Share on other sites

Sounds like a dead short to earth somewhere in that Hi-beam's circuit. Any idea if the car has been smashed on that side? It may have pinched a wire. The latest (for low beam) is probably a matter of time - it was due to happen.

R32 lights are not the brightest at the best of times. I can only suggest a thorough inspection of every component and wire in the circuit(s). Get a small file (nail file ?) into the fuse holder and clean it up.

I can't tell if its ever been hit on that side before. Certainly not since I've had it.

I'll get in there and clean up the fuse connections and see if anything looks dodgy with connections/wires. If I can't see anything and it keeps happening then it'll have to go to an auto elec I suppose....

Thanks for your help.

Fixxxer :P

Wingnam, 15A is what is recommended for the headlights, I would not go higher amperage than this because you are just masking a deeper problem and potentially could do a lot of damage.

Also, a 20A fuse would not help because my fuse is actually melting, when I pull the fuse out it is warped and melted but the actual fuse still seems to be intact.

Fixxxer

Yeah I did a similar trick with my a/c. it kept blowing the fuse, so i put a huge fuse in. Then smoke started coming from under my bonnet and the fuse melted into the fusebox.

Needless to say, I dont recommend putting a larger fuse in. And by the way, my fusebox is fine and my a/c now works perfectly. :D

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...