Jump to content
SAU Community

R32 Gtst Stalling And Power Cutting Out

barnoon

By barnoon,
in Engines & Forced Induction

 Share

Recommended Posts

barnoon Experienced

barnoon

Posted
Posted

Hi guys been having problem with my R32 GTST lately, just some info on it first, stock turbo, gtr front mount, turbosmart bleed valve, pod filter, 3 inch turbo back exhaust, apexi bov.

The problem im having is very intermittent sometimes I can drive with no problems for a whole day ,ive only noticed it happening when the cars warm but sometimes when im around 2000rpm in any gear the car just loses all power, I can put my foot flat to the floor and nothing will happen and then all of a sudden it will jump to 3000rpm then no higher, sometimes after this happens I wait a few seconds then its fine other times it will then stall, when I try to restart the car it is very hard to start and needs me to rev it as its cranking over, sometimes once its restarted it will work fine again and sometimes the whole process will repeat itself, it can happen any time even while cruising along in say 4th the revs will just get stuck around 3k.

Ive also noticed since this problem started the car is idling quite low sometimes around 400rpm.

Any suggestions what it could be as its doing my head in,

thanks guys.

d0p3y Grand Master

d0p3y

Posted
Posted (edited)

Hey Guys,

Dave & I cleaned the AFM on his car last night. So far it seems a bit better but time will tell as it hasn't been taken for a good drive yet. Will let you know how that goes. If you have any further suggestions or comments let us know!

FYI; It's running 11psi.

Ryan

Edited by d0p3y

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...