Jump to content
SAU Community

**please Help** How To Make Resistor Pack

CATKICKER

By CATKICKER,
in Engines & Forced Induction

 Share

Recommended Posts

CATKICKER Mentor

CATKICKER

Posted
Posted

Hi All, I need to make a resistor pack for my RB20DET to fit in my GTR injectors and I am unable to find instructions... I am guessing they would be somewhere or that someone has done it so I would love it if someone would take to time to point me in the right direction.

I don't have a stock GTR resistor pack and need to get them in tonight / tomorrow otherwise Ican't get my car tuned with them this weekend :)

Thanks in advance!!

Josh Grand Master

Josh

Posted
Posted

Dunno about making one, have you tried searching for it?

You could call an import wrecker to find a GTR one.. I also remember reading somewhere that you can use the resistor pack out of an R30..

doing a search would be your best bet on finding the instructions tho, if there are any..

CATKICKER Mentor

CATKICKER

Posted
  • Author
Posted

Thanks mate, I can't find anythng concrete so I though someone may have done it...

I really need to have it and installed by Friday befor Dr Drift comes down (to Tassie) so I figure making one may be quicker than finding one and getting it here! (And a lot cheaper).

Cubes Grand Master

Cubes

Posted
Posted

There's a wiring up guide done by ROY in the tutorial section, I dropped in new injector plugs/boots (To suit VL, VL inj. plugs are the same as GTR inj. plugs, 6 inj plugs/boots cost me ~$53) while I was there as it was a real pain in the arse to trim up all the injectors so the plugs were suitable.

With regards to making a resistor pack. Buying the high quality resistors that it requires will cost you all up around $100. You are better off simply buying a second hand gtr resistor pack for the same/similiar price.

OR... Do what I did and used an Aussy R30 Skyline resistor pack, R30's are everywhere at the old car wreckers. I've seen them go anywhere from $5 right up to a whopping ~$15. :happy:

  • 1 month later...
huddy Veteran

huddy

Posted
Posted (edited)

sorry to bring up an old thread...

but so its confirmed 100% that gtr injectors can be run with a r30 resistor pack - using stock ecu / power fc ...

also where is it exactly located in the r30 and what does it look like (exactly)

and what does an r30 look like hehe - what year?

thanks :(

-Matt

Edited by huddy
Cubes Grand Master

Cubes

Posted
Posted

The R30 uses the usual automotive plug 8pin plug that is made by various manufactures such as navara etc. They can be picked up from the local auto store for around $3.95.

Have a look in the tutorials section for a guide + pics written by Roy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...