Jump to content
SAU Community

Quick Question

Shell

By Shell,
in Victoria

 Share

Recommended Posts

Shell Grand Master

Shell

Posted
Posted

ok, so i need to get from the Airport to the Casino on Friday..

is the Skybus thingy the best/easiest way?

how much would a cab be roughly?

and do trains not go there at all??... just going by the airport site, they're not mentioned?

http://www.melair.com.au/to_from_airport/

thanks for any advice :huh:

Link to comment
https://www.sau.com.au/forums/topic/111498-quick-question/
Share on other sites
funkymonkey Grand Master

funkymonkey

Posted
Posted

Yeah catch the skybus to the last stop, when you get there walk towards the big sign that says crown.

Skybus is $18 I think (or free if the driver's a ncie guy and you have a boarding pass on you). Bus takes about 20 mins by freeway.

Link to comment
https://www.sau.com.au/forums/topic/111498-quick-question/#findComment-2055898
Share on other sites
Shell Grand Master

Shell

Posted
  • Author
Posted

haha.. lifts greatly appreciated but thats not why i'm posting this :no:

James: 11.30am

yeah i thought the taxi would be a bit more...if there were a few of us i'd just get one anyway but i'm flying in on my own so $50 is a bit steep..

I think the bus is the go..

$15... leaves every 10mins... and after the main drop off place, you can apparently jump on one of their shuttle buses and they'll take you to your hotel for no extra charge.

Link to comment
https://www.sau.com.au/forums/topic/111498-quick-question/#findComment-2058830
Share on other sites
Leewah Veteran

Leewah

Posted
Posted

Skybus is defiantely the best option if there's only one person travelling.

As everyone has said, Crown is only bout a 5-8 min walk from the Skybus terminus. Just head DOWN the hill of Spencer St, rather than up coz you'll end in North Melb and that's the wrong way :no:

Link to comment
https://www.sau.com.au/forums/topic/111498-quick-question/#findComment-2058990
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • GTSBoy
      Nissan fuga 450gt android screen

      By GTSBoy · Posted

      What about if you just give it direct 12v and earth?
    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...