Jump to content
SAU Community

Recommended Posts

OK

What the problem is there is a door in ur air conditioning under the dash.

When you press cold the door opens and cold air from ur airconditioning system comes out. When you press hot it closes the door on the cold and lets hot air come through.

That little arm thst moves the door isnt moving, the cold door is closed hense hot air

on my r32 i had the same problem but if i held down the cold arrow it would go into "FC" mode this was the only thing that made the cold air door open

i dunno if its the same on r33's

Link to comment
https://www.sau.com.au/forums/topic/111715-air-con-problem/#findComment-2060534
Share on other sites

OK

What the problem is there is a door in ur air conditioning under the dash.

When you press cold the door opens and cold air from ur airconditioning system comes out. When you press hot it closes the door on the cold and lets hot air come through.

That little arm thst moves the door isnt moving, the cold door is closed hense hot air

on my r32 i had the same problem but if i held down the cold arrow it would go into "FC" mode this was the only thing that made the cold air door open

i dunno if its the same on r33's

Ill try that and see :(

Link to comment
https://www.sau.com.au/forums/topic/111715-air-con-problem/#findComment-2060933
Share on other sites

  • 1 month later...

As suggested above, make sure the compressor is clicking on and engaging when you start the aircon. If it's not doing that, you have either an electrical problem, or the aircon needs to be regassed. With no pressure in the system, the aircon won't engage.

Another problem which can occur is when the dash has been removed at some stage, there is a little plug which goes into the back of the dash airtemp sensor. It can be easily knocked out, and the climate control won't work, thus blowing hot air all the time....although if you set the aircon to coldest setting you should get cold air.

R33, the sensor is in the dash to the left of the steering wheel, there is a little grill you can see in the dash. On the R32, its located in the centre console area I think to the left of the gear lever.

So check to see if you get cold air when on coldest setting, if you don't and you can't hear the aircon compressor activating, you most likely need a regas. This will mean the system is leaking somewhere, hopefully not in the evaporator which is behind the dash :cheers:

As suggested above, it could also be the actuator which opens and closes the door allowing hot or cold air to flow. IMHO, that would be the last thing to check.

When all else fails, aircon specialists should find the problem in no time.

Link to comment
https://www.sau.com.au/forums/topic/111715-air-con-problem/#findComment-2136504
Share on other sites

  • 3 weeks later...

I have a similar problem- my compressor clicks on seemingly (rev's jump) though I only ever get ambient temp air coming out, even at FC. I keep blowing the same A/C fuse though, I've done it over and over, it only blows when I turn on the A/C - not during normal fan/heat operation. The fuse is #8 in the diagram below (R32 under-dash panel). The other A/C fuse (#17) never blows.

R32-Int-fuse-blk.jpg

I figure I have a short somewhere, but where should I start looking? Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/111715-air-con-problem/#findComment-2194886
Share on other sites

I have a similar problem- my compressor clicks on seemingly (rev's jump) though I only ever get ambient temp air coming out, even at FC. I keep blowing the same A/C fuse though, I've done it over and over, it only blows when I turn on the A/C - not during normal fan/heat operation. The fuse is #8 in the diagram below (R32 under-dash panel). The other A/C fuse (#17) never blows.

I figure I have a short somewhere, but where should I start looking? Any ideas?

#8 fuse is the fuel pump. I think you mean #10, in which case your windings are probably shot; there are some tests in the workshop manual you can run. If it is your windings, your looking at ~$120 and a day or two of work. See the tutorial I posted about removing and repairing it.

Fuse guide:

http://www.skylinesaustralia.com/forums/in...md=si&img=47849

Link to comment
https://www.sau.com.au/forums/topic/111715-air-con-problem/#findComment-2195039
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...