Jump to content
SAU Community

Recommended Posts

what you could do with it. is mount it so the filter is facing the radiator. sure its not having air forced in to it. but its also not sucking hot air. the air hitting the back of the filter housing would act similar to an intercooler as it would get cooled by the air. or mb that just works in my head.

personally i would go for a pod in the engine bay with a good cold airbox and a cold air feed. removing the little rubber thing about the passangers side headlight helps get a little more air in there :D you can run a cold air feed with out cutting in to the body. just run it up behind the drivers headlight. i have had 2 PVC pipes running to it. and i have also had a bit of metal bent up with sides to direct the air up there.. both of those workd alright.

if u mount in front of radiator, dont expect radiator to work as well.

also dont forget that if rain needs to get in on a 45 deg angle to get in, that u dont need 45deg angled rain to do this - you only need you car to be moving forward at a decent speed

your largest raindrops have a terminal velocity of about 30-35km/h - so to get rain to come in at a 45deg angle, you only need to be driving at that speed.

your average light rain or drizzle is around the 15km/h mark, so again you only need to travel at that speed for the rain to be coming in at 45deg.

travel twice the speed its now coming in on a 60deg angle - and quickly you see how easily it will be for water to get in there if its facing an open airflow from front of car

if you look closely the front mount air cleaner has a perspex plate in front of it with holes in it and spaced out from air cleaner , i dont think water would be a problem , water injection anybody ? cooling possibly a problem ,depending how close mounted to radiator .

if u wore shoes with holes in them, would your socks get wet when it rains? no different here

they are purely for rice factor, it that isnt already bleedingly obvious. if your even considering them then you know the ricer inside of you is in control more than the logical minded skyline owner.

mate each to there own , i feel the ram pod style is the best from experience, just everybody was complaining about water problems,there is a deflector on it to reduce the problem ,a little bit of water cant hurt a motor ,but if you go through a creek .....

its no longer a ram pod if its got persplex in front of it. its got the worst of both worlds - no forced air assisstance, and it still gets wet if its mount where its visible (as you would, so u can show it off of course :P)

This airfilter may be ideal for bonnet scoop applications where the scoop sits center of the bonnet above the rocker cover just like a top mount intercooler.

but yeh still seems a bit rice for me, im simple... pod, sheild and ducting :P

Edited by adox

if your going to have ducting to your pod filter you can make sure its not aiming at your pod so if any water gets in there it dusnt go strait in your airfilter or you can block off the hole either in the engine bay or in the front of the bumper. when its raining the air is gennerally colder so you will still feel some benifits of the colder air.

easyest way for cold air.. remove the headlight :P even tho it dus look arse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...