Jump to content
SAU Community

Recommended Posts

hey.

i have had my plenum on my RB20DET modified to relocate the throttle body from the side to the front.

at the front of the plenem there used to be the coolant lines goin to it and a few others.

now where should i hook up these coolant lines? should i block em off or put a T-piece and join the three together?

them vacum for the pressure reg i presume just get from anywhere on plenum.

the oil breather one is taken care of via catch can.

ive included a few pics of my setup and a standard so you know what im on about.

any help would be great.

cheers

post-25760-1144565792.jpg post-25760-1144565234.jpg post-25760-1144565358.jpg

Edited by VLT020
Link to comment
https://www.sau.com.au/forums/topic/112915-modified-or-aftermarket-plenums/
Share on other sites

That 10mm bolt that isnt there anymore is used to bleed the air out of the cooling system, maybe making up a....... um how do i explain it..... water tank that the lines will run into with a cap or bleeder on top so you can still bleed the system might be the best bet.

im gussing the RB20 has the water feed through the throttle body like the R33 .. what did they do with that?

i have the plazmaman planum and there is no bleed for the radiator... just have to be patient on bleeding the radiator manualy via the turbo water feed, or the rad cap.

im gussing the RB20 has the water feed through the throttle body like the R33 .. what did they do with that?

i have the plazmaman planum and there is no bleed for the radiator... just have to be patient on bleeding the radiator manualy via the turbo water feed, or the rad cap.

i got plazmaman plenum too. awesome gear!

don't forget if you block that water line off where it goes too after the throttlebody!!! it feeds your turbo!

id personally block the throttlebody off and run a fresh line to the turbo. Im getting a header tank and doing away with the bleed on mine.

Edited by PHaT MR30
don't forget if you block that water line off where it goes too after the throttlebody!!! it feeds your turbo!

id personally block the throttlebody off and run a fresh line to the turbo. Im getting a header tank and doing away with the bleed on mine.

You sure about this one ?? I have the line blocked off for my throttle body and the turbo still gets water. Doesnt the turbo line feed from the back of the plenum ?? and then back into the side of the block ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...