Jump to content
SAU Community

Recommended Posts

Does the R32 GTR kit come with the 3 smaller gauges kit as shown in the first picture or only the kit for the main dash cluster?

Is this group buy still open? I'm keen, also want the 3 gauge background aswell. Cheers.

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Is this group buy still open? I'm keen, also want the 3 gauge background aswell. Cheers.

Sorry mate, Its kezza from a mates computer, but yeah the GB is now closed sorry mate!

But if i get enough interest ill do yet another one!

I need at least 5 people wanting bezels or dials to get an order, so if ya got any mates that may be interested in some dials or a set of sezels i can hook you guys up with them.. But for now its closed, sorry!

kezza

sorry guys, i was waiting one one guy for confermation on payment, its all set and dials and bezels set have been ordered. It should take about a week max two to get them from japan, and a few days for me to get them all ready and posted to your door!

Onc e again sorry for the delay in the time line on this GB, we had a few slow pokes, YOU KNOW WHO YOU ARE, lol

Thanks for your patience guys!

kezza

  • 2 weeks later...
sorry guys, i was waiting one one guy for confermation on payment, its all set and dials and bezels set have been ordered. It should take about a week max two to get them from japan, and a few days for me to get them all ready and posted to your door!

Onc e again sorry for the delay in the time line on this GB, we had a few slow pokes, YOU KNOW WHO YOU ARE, lol

Thanks for your patience guys!

kezza

Hey Kezza, whats the update on these? Its been close to 4 weeks now since payment...are they here yet??

Thanks.

Jon

ok, the dials and all the bezels have been ordered, and mike has now got the dials and bezels. now he is sending them to me :D

Shouldnt be too long now guys, cant wait to get the bezels into my cluster, WILL LLOOOOKKKK HOTT!

Got them today and fitted bout 10 mins ago!! Thanks Kez!! Here are some piccies...R34GTT auto bezel. FYI, they fit perfectly, just getting to the dash was a bit tricky...otherwise all good.

Enjoy! :nyaanyaa:

post-6973-1152605800.jpg

post-6973-1152605826.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...