Jump to content
SAU Community

Recommended Posts

Things for sale

  • JUN Titanium Retainers for RB26 $700
  • JUN Drag Cams Inlet 292/12.50mm Exhaust 320/12.00mm 800
  • R34 GTR Wheels AS NEW $2500
  • Pirelli P-Zero 275/35/18 Tyres Brand NEW $600 pair
  • R33 GTR Passenger Airbag $300
  • Nimso FPR $150
  • Chromes factory RB26 Fuel Rail $150
  • Apexi BOV's suit GTR $300
  • PWR GTR Replacement cooler $500 Brand NEW

The JUN retainers and cams have only been used for a dummy assembly.The R34 GTR wheels are like new and haven't a mark or blemish on them they also come with center caps.Pirelli tyres are brand new and will fit the R34 GTR wheels, I can also supply a used set of front to match for use on a GTR.

Located in Inner City Sydney

Please contact me via PM or 0424-519-298

post-26913-1145245505.jpg

post-26913-1145245601.jpg

post-26913-1145245640.jpg

Edited by BlownNBoosted
Things for sale
  • JUN Titanium Retainers for RB26 $1000 negotiable
  • JUN Drag Cams Inlet 292/12.50mm Exhaust 320/12.00mm $1000 negotiable
  • R34 GTR Wheels AS NEW $3000 negotiable
  • Pirelli P-Zero 275/35/18 Tyres Brand NEW $800 negotiable

The JUN retainers and cams have only been used for a dummy assembly and I am willing to sell them as a set for $1500 (cams and retainers).

The R34 GTR wheels are like new and haven't a mark or blemish on them they also come with center caps.

Pirelli tyres are brand new and will fit the R34 GTR wheels, I can also supply a used set of front to match for use on a GTR.

Located in Inner City Sydney

Please contact me via PM or 0424-519-298

would it be a good guess to say the cams and retainers wont fit an rb25det?

DanielSon: PM Sent

To anyone else interested these can be fitted to RB25 heads once you have converted to solid lifters.

DanielSon: PM Sent

To anyone else interested these can be fitted to RB25 heads once you have converted to solid lifters.

Also RB25 NEO's have solid lifters and any GTR cams can be direct replacement.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...