Jump to content
SAU Community

Recommended Posts

hey

i just bout my first R32 GTR on the weekend and i love it but my question to you all that have on is what can i do to the exterior to make it more of a head turner. if any body has any pics of there R32 GTR head turner u would be a grate help if you could post them to me .

best regards Vlad Adam

Link to comment
https://www.sau.com.au/forums/topic/116976-r32-head-turners/
Share on other sites

yes for a 32 GTR all you need is:

good paint

maybe some nice aero mirrors

nice wheels (personal choice is 33 GTR wheels, or 34 GTR wheels, TE37s, or those BBS LMs as posted above)

a bit lowered

then you're done.

yes for a 32 GTR all you need is:

good paint

maybe some nice aero mirrors

nice wheels (personal choice is 33 GTR wheels, or 34 GTR wheels, TE37s, or those BBS LMs as posted above)

a bit lowered

then you're done.

Yep, subtlety is the key, especially with R32's.

I can't find a pic of mine on this computer at the moment but as everyone else has said just add some nice wheels, clean paint, & lower it.

Mine has TE37's, carbon bonnet, front spoiler, gandor aero mirrors, coil overs and no rear spoiler....

I personally think it looks hot! I like the understated mean look of the 32 when just simple things are done to them.

We'll my gts-t type-M is canary yellow, that turns heads :wub: (and possibly stomaches)

I thought it was too rice at first, now i like it, suits the curves of the car, had to be subtle with the rims though or itd end up ricey.

oh and, nice rims, n1gtr they look great on the car.

here is mine..

you dont have to spend much to get them looking good..

mine is lowered on wheels that cost $700 with tyres!!

i dont have any side skirts either (not even the stock ones)

(stickers have been removed since pic)

Hey buddy, I wouldn't mind knowing what suspension you have. That's an awesome ride height.

Congrad on your buy, what ever you do just dont rice it up that will turn heads in a negative way haha. Like the rest have said just keep it simple get a set of Jap light weight rims, a kit and a paint job. What colour is your car by the way? Yellow is a colour that always attracts alot of attention.

its hard 2 improve on perfection!!! but lowering, nice nims, clean paint, custom plates and dont remove your wing! (personal choice) i prefer go than show, mine is near stock looking but imaculate and gets plenty of looks. fit a wild body kit and the cops never leave u alone! thats why i have gone back 2 stock, but i still get pulled over at least once a week, but never defected.

if its a 32 gtr it does not need anything except maybe a decent set of deep dish rims and dumping it lower to the ground they are perfection straight from the factory so they beed stuff all to be head turners.mine is stock except for wheels and turns heads every day

post-23730-1147698198.jpg

phat, never saw your wheels before, im impressed,

reckon the ass would look a little ugly with the wing but gt wings always look good from front and sides, hti from azz end

impressed though,

druzila, noice show car styles, seeing your ride hight makes me think daily fun isnt in it's repitoire

cant wait to be able to afford a 32r weekend runner

prolly be goind for allot of the stock look with lipidge and skirts

for now my 33t will do, she's a fun mobile, daily fun, but fun love it

Edited by gts-4 dreamer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...