Jump to content
SAU Community

Rb20 Motor, Gearbox, Etc; Package

rb20inside
 Share

Recommended Posts

rb20inside Community Regular

rb20inside

Posted
Posted (edited)

for sale:

93 rb20det motor package

approx 75,000kms

includes complete motor, gearbox, flywheel, clutch, manifolds, turbo

also included: r32 crossmember, engine mounts, gearbox mount, tailshaft, radiator

all parts included add up to almost a complete front cut

prefer to sell it all together or if to different buyers most parts at once

reply to pm as i dont check the thread much

located near(west) brisbane

if i cant get a buyer does anyone have/know of a cheap s13 or r32 i could put it all straight in?

other parts on offer include:

*microtech LT8S. incudes hand controller, lume, sensors, etc. sold

*3in dump/front pipe (one piece, bell mouth style not split)

*greddy intercooler (some stone damage as expected) includes piping if you want it. $250

*apexi twin chamber bov. $150ono

*z32 hubs and spindles. $100ono

*gtr injectors. sold

*s2 rb25 turbo. guess you could say its blown. has a bit of shaft play and is a bit noisy/squeals. great for rebuild/hiflow. $200

*s14a complete rear cradle (includes cradle, lsd diff, halfshafts, all control arms etc, hubs/5stud spindles, swaybar, rotors, calipers, handbrake cables, etc. $500

Edited by rb20inside
Link to comment
https://www.sau.com.au/forums/topic/117346-rb20-motor-gearbox-etc-package/
Share on other sites
dbo Enthusiast

dbo

Posted
Posted (edited)

microtech LT8S. incudes hand controller, lume, sensors, etc

Whats this worth? Guessing it was on your RB20?

edit: wait the LT8S is traditionally 4x injector 4x spark.. so this doesn't fit on an RB20?

Edited by dbo
rb20inside Community Regular

rb20inside

Posted
  • Author
Posted (edited)

price is $300 for the gtr injectors. condition is fine although i havn't had them flow tested, they came out of a running gtr and were only pulled out as they were replaced by sard 720cc items.

the microtech came from a running rb20det so is a 6 injector/spark output unit. it includes/sliced into a rb20 wiring lume.

now that you mention it i am unsure as to whether its a lt8s or ltx8s (as its at a mate house, sorry guys but i will find out for sure)

i was under the impression the lt8 and older mtx8 were the 4 output units whereas the lt8s was the 6 cylinder unit. but in saying that i've seen a lt8 used on a r32 gtr.

anyway it works with and came from a rb20

after about $1000

Edited by rb20inside
rb20inside Community Regular

rb20inside

Posted
  • Author
Posted (edited)

have checked. the microtech is definitely a LT8S. it can run a 6cyl/output car

anyone got a cheap (non turbo auto??) s13 they dont want?

Edited by rb20inside
Alainuae Apprentice

Alainuae

Posted
Posted

hey mate you still looking for the cheap silvy? i got one ready for a rb20 to drop in. I was about to do the same myself as i have the RB20DET engine and nearly all the parts even the r32 box ready to just go in but im willing to sell the car as is (old ca18de box aswell ripped out) So its ready for the rb20 to go in.

So let me know how much u are willing to spend if you want it and we might work somehting out.

Cheers

Rob

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...