Jump to content
SAU Community

Door Open Sensor

MANWHOR3

By MANWHOR3,
in Car Audio & Electrical

 Share

Recommended Posts

MANWHOR3 Proficient

MANWHOR3

Posted
Posted

Hi guys,

Can someone please help me?

Basically, from what I understand, the door sensors on the r33 are on different circuits. i.e. when the driver's door is opened and the key is in the ignition, there is a chime noise. But, when the passenger door is opened, there is no chime noise.

If i'm hooking up an alarm, how can I get it such that if either door is opened, the alarm will be triggered? i.e. where can I tap into a wire?

The reason I ask is because my alarm installer did a dodgy job.

Link to comment
https://www.sau.com.au/forums/topic/117416-door-open-sensor/
Share on other sites
danielr34 Collaborator

danielr34

Posted
Posted
Hi guys,

Can someone please help me?

Basically, from what I understand, the door sensors on the r33 are on different circuits. i.e. when the driver's door is opened and the key is in the ignition, there is a chime noise. But, when the passenger door is opened, there is no chime noise.

If i'm hooking up an alarm, how can I get it such that if either door is opened, the alarm will be triggered? i.e. where can I tap into a wire?

The reason I ask is because my alarm installer did a dodgy job.

Hi mate go to the thick wiring loom in the drivers kickpanel (to the right of your left foot) and find a thin red wire, it is one of 2 and it is the thinner one out of the 2, you can tell because the other one is a little thicker in diameter.

I have been fitting car alarms for Security In Motion for the past 5 years and if we don't know nobody does!

Next time just call us.

MANWHOR3 Proficient

MANWHOR3

Posted
  • Author
Posted

Can you explain something to me?

The previous alarm installer just soldered a wire onto the actual switch on the driver's door. But as I said above, the passenger's door is on a separate circuit.

So just to confirm, doing this red wire will have it hooked up to both sensors?

Cheers

frx026 Proficient

frx026

Posted
Posted

To Confirm in a r33 the door sensor pick up wire is the thin red wire in the drivers kickpanel.

And as how that has been done, i have to repeat myself

It sound like your car would be fairly easy to steal.

Why?

Well not because one door does not trigger the alarm. But because the original installer obviously had no idea what he was doing. The r33 uses one wire to sense both doors opening, so having only one working means that installer -

- did not have much skill

- does not know skylines

- has probably left the alarm box in your kick panel or just under the dash

- was working to a price

I think what you should do is have a look under your dash, drivers kickpanel to see if you can see the alarm, if you can, dont bother taking it back to your original installer, take it to someone who knows what the are doing and get the entire alarm relocated and rewired.

Sure its extra money, but really from what you have said, it would most likely take less than 30 seconds to steal your car at the moment.

If you are looking to get it done fire a PM at CHRIS ROGERS, he is the man with the install contacts.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted (edited)

no it doesn't.

depending on car they are two different leads in two different spots.

32,33,34 &35 are diode isolated from the drivers door. all have two places to get the wire. I do not get it in the usual spot. colours are all similar.

inthe case of a S2 33 and 34 the smart entry system will foul the alarm if tied in at that point.

Edited by Chris Rogers
  • 8 months later...
Keeper Experienced

Keeper

Posted
Posted
Hi mate go to the thick wiring loom in the drivers kickpanel (to the right of your left foot) and find a thin red wire, it is one of 2 and it is the thinner one out of the 2, you can tell because the other one is a little thicker in diameter.

I have been fitting car alarms for Security In Motion for the past 5 years and if we don't know nobody does!

Next time just call us.

WOOHOO this is so helpful, hey its to the right of your RIGHT foot, I got confused for a little there!

Its the loom that continues back under the carpet along the right side of the car :)

J_Red33 Experienced

J_Red33

Posted
Posted (edited)

I'm not sure this is completely the same problem, but I have an alarm installed that triggers on both doors which are on separate circuits, but the interior light no longer turns on when the passenger side door is opened. My car originally had the factory keyless entry. I'm guessing it's probably a bad idea to brigde the two door wires down at the kick panel. Is there possibly any other way I can overcome this problem?

Was thinking maybe I need to link the interior light circuit to the passenger door switch via a diode, but I have no idea which wire the interior light trigger is.

Any help here would be appreciated. I don't really want to take it back to the installer they were quite rough with my interior trim after commenting how 'Nice & clean' my interior was (GT AUTOSOUND, DON'T GO THERE! If you truely value your car).

Edited by JazzaR33
Chris Rogers Grand Master

Chris Rogers

Posted
Posted
I'm not sure this is completely the same problem, but I have an alarm installed that triggers on both doors which are on separate circuits, but the interior light no longer turns on when the passenger side door is opened. I'm guessing it's probably a bad idea to brigde the two door wires down at the kick panel. Is there possibly any other way I can overcome this problem?

Was thinking maybe I need to link the interior light circuit to the passenger door switch via a diode, but I have no idea which wire the interior light trigger is.

Any help here would be appreciated. I don't really want to take it back to the installer they were quite rough with my interior trim after commenting how 'Nice & clean' my interior was (GT AUTOSOUND, DON'T GO THERE! If you truely value your car).

are you sure the alarm works on bith doors?

bridging the wires will only make the lights on buzzer show on both doors not jst the drivers one.

J_Red33 Experienced

J_Red33

Posted
Posted
are you sure the alarm works on bith doors?

bridging the wires will only make the lights on buzzer show on both doors not jst the drivers one.

Yeah pretty sure it works, confusing I know, but that's the way it's working at the moment. Not sure if it had anything to do with the factory central locking system as both the door wires did go to that. It has been removed so I'm thinking that's the reason.

  • 1 month later...
are33 Proficient

are33

Posted
Posted

This has probly been solved i havnt read through the thread, but i made this a while ago when i disconected mine, Its a bit dodgey but its easy to do if you can make sense of it :P

http://www.boostcruising.com/forums/index....howtopic=167222

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
×
×
  • Create New...