Jump to content
SAU Community

Is It Possible To Bypass The Loom Plug For A Head Unit?

D-limo

By D-limo,
in Car Audio & Electrical

 Share

Recommended Posts

RANDY Veteran

RANDY

Posted
Posted

First, go to Jaycar, Strathfield and Dick Smiths and see if there is a harness adapter for your headunit. (from your unit to ANY car harness)

That way, you don't need to make up the plug or solder wires directly onto your headunit, just plug in, and then crimp the other end of the loom to fit the stock harness.

Failing that, I don't know how easy it will be to work out which pins on the back of the HU are for what. A multimeter will only work when there is power applied, and then finding the right pin for power first go sounds unlikely. If you apply power to the wrong pin, you may blow something up. If you open the unit, a trained eye could probably verify which pin is for what, but that's not me!

D-limo Veteran

D-limo

Posted
  • Author
Posted

The hanesses cost like $45.. And the unit is probably worth that 2nd hand.. So yeah I'm trying to do it cheap as possible lol.

You're right. Finding wich pin is for what is going to be the hardest thing to figure out. I was hoping it was that easy. Can anyone confirm? Also is there spec sheet or the like I should be searching for that would contain what each pin does?

MANWHOR3 Proficient

MANWHOR3

Posted
Posted

You can do it, you have to open the rear cover of the headunint and solder onto the plug socket. trust me mate, not worth the trouble.

If it's not worth buying the wiring plug, then it's not worth installing it like that.

It'll be a shit job. difficult. probably fail too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • wizlb
      Flex Fuel Kit Workshop

      By wizlb · Posted

      Thanks Dose.....    I appreciate it!!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • Piggaz
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By Piggaz · Posted

      I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...