Jump to content
SAU Community

R32 Bonnet And S13 Guards

daler32

By daler32,
in Classifieds

 Share

Recommended Posts

daler32 Proficient

daler32

Posted
Posted (edited)

hi all, just looking for EOI for these parts at the moment as im getting wider front guards and a new bonnet this weekend. so parts are still on the car. guards are white over bronze s13 guards straight as. bonnet is black and straight but has lots of little scratches on it from cats. looking for 100 for both guards or 60 each and 200 for the bonnet. pick up only as i have no way of delivering the bonnet. located in labrador on the goldcoast. Cheers Dale.

also have 4 14x6 wheels. suit 4stud 114.3 pcd. ones a bit bashed up. two have rally tyres on. and the other two have road tyres on em which are mismatched and one of em is buggered. can send pics of the wheels if anyones interested. 100 bucks or best offer for these. will separate the rally tyres from the wheels at buyers expense.

Edited by daler32
Link to comment
https://www.sau.com.au/forums/topic/118293-r32-bonnet-and-s13-guards/
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...