Jump to content
SAU Community

Recommended Posts

hey man runnin your car with no BOV is bad news for the turbo, its stuffs it up and shortens the life of it. Now why would you want to do that!!  

by the way you would get that sound your after, but is it worth it??????

:bahaha: hahaha, u people make me laugh

Danny32, take off the plum back, stick on a metal plate in its place, bolt it in and reap the rewards of flutter

100% that your turbo will be fine in years to come

stick on a pod filter, partition it off to get the sound more audible

leave the bov preachers to their marketing ploy

enjoy

GTS-t VSPEC

throttle response, possibly but through my tests i found that it was THAT noticable

noticable YES, but not to the extreme of some peoples suggestions

Sil8ty

the reason why re circulating valves were placed on engines is for the noise

your regular jo blow buying a turbo car doesnt want to hear flutter so buy putting in the recirulating valve in, u get rid of that slight muffled noise (cos obviously the airbox supresses the noise too) and releave the compressor surge

BUT, alot of the aftermarket bov i see on peoples are ARNT put in properly

for it to work properly with ZERO surge, it should vent at the slightest amount of back pressure just like the factory valve does

nb: no need for the sarcasem Sil8ty, BOV is like debating religion..itll never end

Whistla,

While I do agree that aftermarket BOV's are used excessively and the effect on the car relatively small, I do think that the stock recirc valve is necessary at the very least.

Even with a stock turbo there is a small amount of compressor surge, without any form of BOV, stock or otherwise, then this can cause additional stress on the turbo. While failure is hardly likely, I think that either it or an aftermarket one should be retained.

See'ya:burnout:

DANNY32..

Yes.

If you remove it and block off the holes and vacuum line and so on, you will get the pchu chu chu sound you are after.

if you still have the standard air box, it won't be loud.

if you have a pod filter, then you will hear the sound you are after..

I'm not going to bother with my opinions on the whole bov or no bov theory..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...