Jump to content
SAU Community

Recommended Posts

  • 3 years later...

I believe you simply wrap a flat head screw driver in some a rag and just press on the edge closest to the centre of the car, gently pushing outwards and it should just pop out, or it could be from the outside edge toward the centre of the car, one of the 2, give it a go ;)

Yeah, I had trouble undoing mine when I took the front bar off, since I wasn't changing the indicators, I just unplugged them from the back.

But I heard they need a bit of force to get them out

IMO best way is to reach in behind. You will feel the two steel clips that hold them in place. Simply squeeze, and push forward. I used a butterknife, but found this a bad way to do it, and resorted to my hands. No tools required

Once you get it down pat, you will be glad to know not everyone knows how simple it is... otherwise im sure the nismo clear ones I put in wouldnt have last long around down :P

Sweet, thanks! i will try tonight.

<br />IMO best way is to reach in behind. You will feel the two steel clips that hold them in place. Simply squeeze, and push forward. I used a butterknife, but found this a bad way to do it, and resorted to my hands. No tools required<br /><br />Once you get it down pat, you will be glad to know not everyone knows how simple it is... otherwise im sure the nismo clear ones I put in wouldnt have last long around down <img src="http://www.skylinesaustralia.com/forums/style_emoticons/default/smile.gif" style="vertical-align:middle" emoid=":laugh:" border="0" alt="smile.gif" /><br />
<br /><br /><br />
I believe you simply wrap a flat head screw driver in some a rag and just press on the edge closest to the centre of the car, gently pushing outwards and it should just pop out, or it could be from the outside edge toward the centre of the car, one of the 2, give it a go :laugh:

+1 did da same thing wrap a flat head screw driver with sticky tape and just stick the screw driving on the edge and it will eventually pop out..be careful not to scratch ur paint..i almost did my one..

  • 2 weeks later...
+1 did da same thing wrap a flat head screw driver with sticky tape and just stick the screw driving on the edge and it will eventually pop out..be careful not to scratch ur paint..i almost did my one..

yeah I was afraid of scratching. easy as shit way to get them out is as follows.

1. jack up the side of the indicator your taking out to make access easier if your cars lowered.

2.undo the plastic underpanel.

3. reach up behind the bar and unplug the indicators.

4. feel for the steel clips that hold the indicators in place.

5. squeeze them and push forward.

no paint scratches.

no frustration.

easiest way imo.

Edited by jimmyr31
I believe you simply wrap a flat head screw driver in some a rag and just press on the edge closest to the centre of the car, gently pushing outwards and it should just pop out :)

It took me 10 sec to do it this way. I just made sure that head of the screwdriver was pressed against the side of the indicator with my other hand and NOT levered against the bar at all. :banana:

It took me 10 sec to do it this way. I just made sure that head of the screwdriver was pressed against the side of the indicator with my other hand and NOT levered against the bar at all. :dry:

Weakling Terry :D

I just stick my arm up one of the front vents (love the GTR bar) and squeeze the clips with my fingers.. Just remember to undo the globe or u feel like an idiot afterwards when it gets stuck as u pull it out haha

Weakling Terry :D

I just stick my arm up one of the front vents and squeeze the clips with my fingers.. Just remember to undo the globe or u feel like an idiot afterwards haha

This is exactly how you described your night out with your G/F!!!!! You didn't have the two mixed up did you David???? :dry:

  • 6 months later...

Anyone know how to do this with the stock series 1 front bar? The right side was easy, but I can't reach behind on the left side cos of the oil cooler vent D:

I tried using the screwdriver but it's not popping out. It's f**king shitting me! :blink:

Edited by PewPew
Anyone know how to do this with the stock series 1 front bar? The right side was easy, but I can't reach behind on the left side cos of the oil cooler vent D:

I tried using the screwdriver but it's not popping out. It's f**king shitting me! :)

i also need an answer for this, as well as how to get the side indicators off.

thanks guys

i also need an answer for this, as well as how to get the side indicators off.

thanks guys

The front indicator lugs are at the sides (not top or bottom), and they can collect dirt. I'd spray some 'Tar 'n Bug' Remover to loosen any gunk around those lugs > try with the screwdriver again as above.

The driver's side indicator is removed with a screwdriver too. You stand next to the driver's door and use the flat head screwdriver at the edge of the indicator and push towards the front. It's springy and it'll pop out.

The passenger side indicator is removed by standing next to your front wheel. Use the screwdriver on the edge of the indicator and push it towards the rear.

Hope this helps...

The front indicator lugs are at the sides (not top or bottom), and they can collect dirt. I'd spray some 'Tar 'n Bug' Remover to loosen any gunk around those lugs > try with the screwdriver again as above.

The driver's side indicator is removed with a screwdriver too. You stand next to the driver's door and use the flat head screwdriver at the edge of the indicator and push towards the front. It's springy and it'll pop out.

The passenger side indicator is removed by standing next to your front wheel. Use the screwdriver on the edge of the indicator and push it towards the rear.

Hope this helps...

cheers it does.. do you push 'under' the rubber grommet thing?

thanks

cheers it does.. do you push 'under' the rubber grommet thing?

thanks

No, you'll scratch the paint that way. You push against the hard plastic lens edge.

You wouldn't want to damage the rubber gasket seal lest you let water condensation get in later on.

No, you'll scratch the paint that way. You push against the hard plastic lens edge.

You wouldn't want to damage the rubber gasket seal lest you let water condensation get in later on.

righto, i'll give that a try later, why do they make it so difficult :) i got some smoked indicators off ebay, look pretty good, cant wait to get them in but the seller forgot to ship with the side indicator bulbs.. would you happen to know what size they are and roughly how much? (if theyre cheap i'll just get some locally)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...