Jump to content
SAU Community

Warming The Engine

R33-Lovr
 Share

Recommended Posts

R33-Lovr Enthusiast

R33-Lovr

Posted
Posted

Hi Guys

just thought i would get your opinion on this and see what ppl do,

do you warm your car before you go for a drive either in the morning or afternoon after work and so on, how long do you keep it on for, do you wait for the oil pressure to drop/heat gauge to move ......

i know the oil plays a big part in this i use Motol 4100 turbo light, please note what oil your using..

is it important to warm the car / leave it for 30sec then drive...??

i usually turn the car on have a fag then get it and drive but i dont push it till the car is warm enough...

whats your opinion

Link to comment
https://www.sau.com.au/forums/topic/119021-warming-the-engine/
Share on other sites
gtst25 Proficient

gtst25

Posted
Posted

I don't like Motul turbo light oil. I use shell fully synthetic. Enough on the oil discussions though - it just goes on and on.

As for warming up - I think the best way is to get oil pressure, then take it easy and short shift until it's hot.

Cheers

Frink Veteran

Frink

Posted
Posted

i usually wait till the temp gauge starts to move, then i drive it off boost until its completely warm. and i dont give it some until the gearbox is warm too....

i use Motul 8100. my car is near stock (engine wise..), but i find that it likes the stuff.....

Cubes Grand Master

Cubes

Posted
Posted

Yes indeed use the search button.

You will find in there where I had my motor built with forged pistons etc.

The builder told me to jump in it start the car, put my belt on and drive off slowly down the road. The car comes up to operating temp within ~2km's, which is only a minute or so.

The less time the pistons sit there slapping around the better, not that they slap much but they do slap ever so slightly.

Prolonged warm ups is probably why some of you ppls return poor fuel economy figures.

sloutch Mentor

sloutch

Posted
Posted
hey mate should warm up the car for about 5 mins then drive off on low boost until hot and the oil i use is PENRITE bro.

5 minutes?!?!? That's quite a long warm up. Abit too long i reckon?

I usually let it warm up for a min before i start driving off slowly. All the fluids will then start to get warmed up.

Am using Motul Turbolight. Don't think the engine likes it. Will switch to Motul 8100 in my next oil change.

siddr20 Grand Master

siddr20

Posted
Posted

^^ as in dont let the boost go past postive figures.. Thats what i meant with stay off boost.. and less than 3000rpm or so..

In general just take it easy!!

Im sure you can work it out yourself as each car is different.

And you can notice when the car is still cold..

Common sense really

EvilINGT Community Regular

EvilINGT

Posted
Posted

I let it idle for about 30sec - 1min, just to get some oil in the head, then just take it easy, shifting before 3000rpm, in the time it takes to drive about 1-2ks the oil pressure drops and the engine is warming up 3-4ks its in operating temp.

Also if im sitting/idling for prolonged periods of time, i generally give the engine a little rev every 45 or so seconds.

Castrol Synthetic R 5w-40 as its probably the best i can get where i live. Heard they discontinued it though and replaced it with something else, EDGE i think, ( what do you know, a little search and there it is http://www.castroledge.com.au ) btw anyone know if EDGE is any good?

cheers

Evil

ellie Proficient

ellie

Posted
Posted

I was lucky enough to score an owners hand book with my car which tells you to start the car and as long as the oil pressure light goes out, drive off!

From my mechanical knowledge their are several reasons for this, one of which "cubes" covered = if the motor is cold and left to idle it can glaze your bores etc.

And another one that alot of people don't think about (or don't care because they've gutted thiers) is melting your catalytic converter. when warming up your car by idling the motor is pooring fuel down the exhaust which is still relatively cool a collects in your cat. Then as it heats up it gradually evaporates and burns inside your exhaust and heavily fuel lined cat which over time melts it! I see this a lot on the larger capacity european cars which run that much richer during warmup due to the super cold start ups they're designed for!

As is widely known through the automotive comunity " 90% of engine wear occurs during start up and warm up", so it's always best to follow manufacturers instructions as they know what they've built and the best way to look after it.

Why do you think cabbies get phenominal kms out of a motor before any serious work is required? because they (business going well) don't ever get the chance to cool down. So less wear!

Ronin 09 Grand Master

Ronin 09

Posted
Posted

I start it up and do an 8000rpm clutch dump.

But have any of you considered that no only is the engine oil cold, but so is the tranmission, diffs, transfer case etc

and they do it harder than the engine oil... remember that engine oil is under pressure - tranny and diff oil is just splashing around in there...

and PS change your tranny and diff oil regularly!

/takes off dad-hat/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...