Jump to content
SAU Community

Recommended Posts

drove past there this morning, it was blocked.....

that guy works at UQ, and i have personally talked to him before........very sad.......hes also on BC.

i was told he was doing 180ks or something.....

I saw the little pic. He was moving alright, we kinda guessed it was an RX7 then read the rest of the article. Only 17y/o or something. Sad. But it does go back to the govt and driving training I say (to a point...) If he knew first hand what the speed does then he might not have got in to that situation. But hey, training costs more money than peoples lives.

I saw the little pic. He was moving alright, we kinda guessed it was an RX7 then read the rest of the article. Only 17y/o or something. Sad. But it does go back to the govt and driving training I say (to a point...) If he knew first hand what the speed does then he might not have got in to that situation. But hey, training costs more money than peoples lives.

yeah, i have talked to the kid before.........feel pretty sad, especially after my mates told me what they saw.....

ppl at his age should not have a powerful car like his....end of the story.

Nice engine pics back there Shaneo....

I like the typical 26/30 gap in the front cover... :D

Love it... Looks like you have a fair amount of work left tho... I hate the fiddley bits...

thanks col :)

you wont see the bottom cover when the engine is in, but i wanted to paint it anyway :(

yeh, puttin the sump adapter on and modifying the bits needed to fit the sump will prolly give me the irrites, but ohwell

yeah, i have talked to the kid before.........feel pretty sad, especially after my mates told me what they saw.....

ppl at his age should not have a powerful car like his....end of the story.

i had my previous R33 before i got my licence, and now im only 19 and have a fairly hi-powered gtr. it just comes down to how you drive the thing, and of course "experience".

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...