Jump to content
SAU Community

Recommended Posts

I drove old yella just then...

She went super sonic 28psi down bridgeman road in 4th gear spinning the wheels...

Was a hand full but i got her home with out setting her on fire... :pwned:

It turns out i didnt put the external wastegate correctlly...

This is my first experience with an external and after doing some searching on the web i found a really good description on a jamican car forum...

Thanks Jamica... You have saved me from blowing up my engine...

Ill wait for the car to cool down and then ill go and fix my simple error...

Here are some actual maintenance complaints submitted by US Air Force pilots and the replies from the maintenance crews.

Problem: "Left inside main tire almost needs replacement."

Solution: "Almost replaced left inside main tire."

Problem: "Test flight OK, except autoland very rough."

Solution: "Autoland not installed on this aircraft."

Problem #1: "#2 Propeller seeping prop fluid."

Solution #1: "#2 Propeller seepage normal."

Problem #2: "#1, #3, and #4 propellers lack normal seepage."

Problem: "The autopilot doesn't."

Signed off: "IT DOES NOW."

Problem: "Something loose in cockpit."

Solution: "Something tightened in cockpit."

Problem: "Evidence of hydraulic leak on right main landing gear."

Solution: "Evidence removed."

Problem: "DME volume unbelievably loud."

Solution: "Volume set to more believable level."

Problem: "Dead bugs on windshield."

Solution: "Live bugs on order."

Problem: "Autopilot in altitude hold mode produces a 200 fpm descent."

Solution: "Cannot reproduce problem on ground."

Problem: "IFF inoperative."

Solution: "IFF inoperative in OFF mode."

Problem: "Friction locks cause throttle levers to stick."

Solution: "That's what they're there for."

Problem: "Number three engine missing."

Solution: "Engine found on right wing after brief search."

there is a redhead , a brunette & a blonde having coffee talking about their teenage daughters. the redhead says " i was looking thru my daughters drawers the other day & found a packet of smokes ... i cant beleive my little girl smokes " the brunette says " well i was looking thru my daughters drawers the other day & found a bottle of whiskey ... i cant beleive my little girl drinks" the blonde says " i was looking thru my daughters drawers the other day & found a packet of condoms ... i cant beleive my daughter has a dick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...