Jump to content
SAU Community

Recommended Posts

oh yeha.....touche....stupid shane and him having to go home....bastard.

below me

this dude is selling surge tank setup for $300 excluding the pump

I already have a tank lines and 044 how much would it cost to do the fittlings like the one pictured or would i be better off buying the surge and lines of this guy and sell my current lines and tank? Im guessing I could get $150ish for what I already have.

who does speedflow lines and fittings at a decent price?

so what is it u want to use from that setup he's selling? by the sounds of it u already have the stuff u need...

dont buy speedflow or the like (i use Earl's) in aus, as its all waaaaay too expensive. i have bought all my gear from the states (summitracing.com) however i may have found a supplier up my way who can beat the us prices...

i hope ur pockets are deep if u wanna play with braide >_<

shanef will know....where is the bish when you need him.

here now :D

im waiting for him to come and answer it for me :) any other ideas welcome!!!

also shane what are the possibilities / complications of running an aftermarket rb26 fuel rail and injector on my 25 I dont want to have to forkout for injectors again once it is 26 time. PFC running it.

problems i can see are

1) fuel rail bolt locations (rb25 side feed, rb26 top feed, rails have differing bolt locations on the plenums)

2) Injector driver in ecu/resister pack. (rb25 high impedence, rb26 low impedence, hence the resister pack on rb26's)

3) o-ring on 'bottom' of injector. the one that seats in the plenum. i've got a feeling theres some difference there too

Afternoon weirdos. I'm going to check out a car this afternoon... man am I pissing myself with excitement!!1

is said car going to sound like this?... ASS ASS ASS ASS ASS

:spank:

annananananananananananananananananananananannananananananan

hi

gl with the car!

fark you then miss ignorant :D

ok so could you do the lines in the picture for less than $200 bucks new? appprox? im guesing not even close aye

those lines and fittings look hawt and will ad 11kwatw

depends where they go to under the car...

PICSORBAN BISH

I haven't been to see it yet so these two are just from what he's given me and they're only little...

post-6756-1190551587_thumb.jpg

post-6756-1190551632_thumb.jpg

annananananananananananananananananananananannananananananan

hi

gl with the car!

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

hi :D

dan, u have a 33 right? them lines in that pic are to suit a 32, so the length's wont be right for ur car (u need them longer) plus a few of the fittings would have to be changed

fark you then miss ignorant >_<

depends where they go to under the car...

f**k off.

I haven't been to see it yet so these two are just from what he's given me and they're only little...

post-6756-1190551587_thumb.jpg

post-6756-1190551632_thumb.jpg

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

lizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizz

izzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzl

zzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzli

zlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzlizzliz

hi :D

hey darlin, how are you?

hey darlin, how are you?

I'm really good :D I started my beauty stuff so i'm on my way to finally having my own little career. I've already had a few randoms volunteer for waxing :sorcerer:

How's you? How's your car going I haven't heard about it in ages.

he said it includes everything you need to install im guessing this all just links up to the stocko lines under the car.

from what i can tell it will be everything bar the nos setup in the photo

hahaha good work!!!

I'm ok! But of a shitty mood today. Actually... a feral mood! My head is spinning, my shoulders ache, I'm waiting on results from a medical test before the place I wanna work at will issue me with an offer. My car is a little fooked.... that sums it up!

I saw pics of the car you're looking at! I'm excited!

its ok, i dont want to be associated with a pair of silvia owning females anyway >_<

Sweet as. I usually don't like to hang with mummies boys who collect garden ornaments for fun either :D

hahaha good work!!!

I'm ok! But of a shitty mood today. Actually... a feral mood! My head is spinning, my shoulders ache, I'm waiting on results from a medical test before the place I wanna work at will issue me with an offer. My car is a little fooked.... that sums it up!

I saw pics of the car you're looking at! I'm excited!

oh shit hey... *anna yells penis at liz* hahahah see I knew that'd cheer you up :spank:

I hope your test results come back with something good, are you looking at moving on from your job?

Yeh the car is a little dinged up and the engine is buggered but it's all good. That's what I was after haha

dan, u have a 33 right? them lines in that pic are to suit a 32, so the length's wont be right for ur car (u need them longer) plus a few of the fittings would have to be changed

shit didnt even think of that!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...