Jump to content
SAU Community

Recommended Posts

hihihihih what's up bunta?!

not alot! I'm just starting my 4 weeks bludging at work!

do new injectors come with new seals?

haha sounds like fun! i take it you decided which job to take?

i know sards dont

thats because thet are f**king POV spec

anything that is good will come with new seals Liz

some may not like to pay over/close to 1k for a set of injectors, then u have the farktards that dont give a rats

they all do the same thing u douch

some may not like to pay over/close to 1k for a set of injectors, then u have the farktards that dont give a rats

they all do the same thing u douch

by the time you buy all the other crap that sards need like collars and suff you are paying nearly the same anyway! And sif pay nearly a grand...you need some sweet hookups

by the time you buy all the other crap that sards need like collars and suff you are paying nearly the same anyway! And sif pay nearly a grand...you need some sweet hookups

other crap like 20c seals, a bit of wire & a bit of solder? yeh couple hundred right there fo shizzle :rolleyes:

did someone say seal?

50459933.JPG

hahahaha

haha sounds like fun! i take it you decided which job to take?

i know sards dont

yeah i got offered a better job at the same company.. didn't take much deciding!!! LOL

there was a miss understanding when we discussed the pay! I thought they meant including super, but they meant excluding... so I get more! LOL

by the time you buy all the other crap that sards need like collars and suff you are paying nearly the same anyway! And sif pay nearly a grand...you need some sweet hookups

ok, I was thinking nismo or hks..... john (silver gts-t) says no to sard.

so those ones will come with the seals?

I was thinking of picking up a set of second hand for 450, but then i reaslied I can get new ones for 480, and then i get the seals with them too! rather than using second hand seals.

other crap like 20c seals, a bit of wire & a bit of solder? yeh couple hundred right there fo shizzle :rolleyes:

last time I looked the collars were $36 each and why would anyone spend ages soldering shit on when for like $200 more you can plug it in?

hahahaha

yeah i got offered a better job at the same company.. didn't take much deciding!!! LOL

there was a miss understanding when we discussed the pay! I thought they meant including super, but they meant excluding... so I get more! LOL

ok, I was thinking nismo or hks..... john (silver gts-t) says no to sard.

so those ones will come with the seals?

I was thinking of picking up a set of second hand for 450, but then i reaslied I can get new ones for 480, and then i get the seals with them too! rather than using second hand seals.

Both HKS and Nismo are good Liz just get wahtever is cheaper on the day!

last time I looked the collars were $36 each and why would anyone spend ages soldering shit on when for like $200 more you can plug it in?

its like trying to have an arguement with a woman/brick wall, u can never win :rolleyes:

ok.. but they include everything right?

yessum

its like trying to have an arguement with a woman/brick wall, u can never win :rolleyes:

I think you would find if you were ever right about somthing you would win a lot more arguments

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...