Jump to content
SAU Community

Recommended Posts

As if 4 weeks. I usually get parts (if the parent company eg. Nismo, HKS etc. have them in stock) within 7 days. Never more than 14 unless there is a stuff up with payment or something.

U suck at my manifold question bitch

Ive never had something come from nengun or greenline in less than 3 weeks...

Ever

Im sure it happens, but their websites do say allow up to 45 days for orders to be filled...

I suppose you are right. But then again, I don't use Nengun or Greenline. They DO take way too long. 3 months on my injectors a couple years ago and various lies to cover their arse. That did it for me.

hi.

This is Joshwa

post-21318-1191557092_thumb.jpg

akaNismo Boy Joshwa's Myspace

Now my friend Joshwa wants his face and emo haircut to dominate Sau. as a joke between us Queenlanders. now joshwa is aware of this and actually is interested in this lil project we have his full permission. so if you want to be part of something that will hope fully catch on please copy joshwa into ur signature or avatar.

thanks

Mark

Copy this code into your Signature to have joshwa's face gracing SAU. (just delete the "*" when you put it in ur signature)

[img*]http://www.skylinesaustralia.com/forums/uploads/post-21318-1191557092_thumb.jpg[/img]

My Hero Joshwa

And can u do that and what will it cost:

if i gave you the turbo, the waste gate, the BOV and the cooler.

Shit man. Wouldn't be too hard I can't imagine. Not sure on cost. Start at $1000 and we'll trim it down from there :yucky:

hehe, just kidding. But really, too hard to quote. How does - cheaper than anywhere/anyone else - sound?

cost will also depend on whether you want stainless or mild.

Also, why does the exhaust loop around and come back on itself? That's a bit silly, or can it only exit from that side?

Shit man. Wouldn't be too hard I can't imagine. Not sure on cost. Start at $1000 and we'll trim it down from there :yucky:

hehe, just kidding. But really, too hard to quote. How does - cheaper than anywhere/anyone else - sound?

cost will also depend on whether you want stainless or mild.

Also, why does the exhaust loop around and come back on itself? That's a bit silly, or can it only exit from that side?

Quick mock up in paint, ATM, we run a different manifold to retain the heater box's (air cooled motor), as we dont want to ditch the heater, i need to track down some other manifolds that exit (as seen in paint pic). It could be done a lot easyier if i bought "extractor manifolds" but the heater box's must stay.

So, as you can see when i track down due exit ones (3.0lt ones) they will have a duel exit to use the "cross over pipe" It's hard to explain unless u have seen the porsche heater box's off the manifolds. in theory u could cut an shut the ones on there, but thats a bit of work

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...